AMX AXB-DMX512

AMX AXB-DMX512 bruksanvisning

(1)
  • Installation Guide
    AXB-DMX512 DMX512 Interface
    Overview
    The AXB-DMX512 DMX512 Interface (FG5927) creates a bi-directional DMX512
    AXlink connection, transmitting and receiving up to 512 DMX channels for
    lighting dimmers, spotlights, and other DMX control applications.
    Onboard processing and memory can create and store channel groups, faders,
    patches, and up to 72 presets. A DMX lighting board can operate in tandem with
    the AXB-DMX512, generate levels for storing presets, or pass through the AXB-
    DMX512 for direct control of channels.
    Specifications
    Setting the Device DIP Switch
    The 8-position DEVICE DIP switch on the front panel (FIG. 1) sets the AXlink
    identification number for the AXB-DMX512. Make sure the device number
    matches the number assigned in the Axcess software program.
    The following table describes the values on the DEVICE DIP switch.
    Terminating the Device
    When using the DMX input and if this device is the last device in a chain of
    DMX512 devices, you must terminate the line. To terminate the device, position
    jumpers on jumper pin trios JP4 and JP5 (FIG. 2):
    1. Remove the jumper that is on pins 1 and 2 of jumper trios JP4 and JP5.
    (Pins 1 and 2 are marked HIZ - see FIG. 3).
    2. Place the jumper on pins 2 and 3 of jumper trios JP4 and JP5. (Pins 2 and
    3 are marked TERM -see FIG. 3). This terminates the incoming DMX input
    with a 120 ohm resistor.
    Wiring Devices to the AXB-DMX512
    The AXB-DMX512 has three captive-wire connectors on the rear panel (FIG. 4)
    for DMX512 transmit and receive, and AXlink.
    Preparing/connecting captive wires
    1. Strip 0.25 inch of wire insulation off all wires.
    2. Insert each wire into the appropriate opening on the connector according to
    the wiring diagrams and connector types described in this section. Do not
    tighten the screws excessively; doing so may strip the threads and damage
    the connector.
    Wiring guidelines
    The interface requires a 12 VDC power to operate properly. The Central
    Controller supplies power via the AXlink cable or external 12 VDC power supply.
    The maximum wiring distance between the Central Controller and interface is
    determined by power consumption, supplied voltage, and the wire gauge used
    for the cable.
    FIG. 1 AXB-DMX512 (front view)
    AXB-DMX512 Specifications
    Power consumption 160 mA @ 12 VDC
    Power supply 12 VDC
    Front panel components:
    LED Indicators AXlink LED (green and blinks to indicate AXlink
    communication activity and power:
    Full-Off indicates no power is being received or the
    controller is not functioning properly.
    One blink per second indicates power is active and
    AXlink communication is functioning.
    Full-On indicates there is no AXlink control or activity,
    but power is On.
    RX LED (red) indicates the AXB-DMX512 is receiving
    DMX512 data. Corresponds to the IN and OUT ports
    on the rear panel.
    TX LED (red) indicates the AXB-DMX512 is
    transmitting DMX512 data. Corresponds to the IN and
    OUT ports on the rear panel.
    DIP switch 8-position DEVICE DIP switch sets the AXlink address
    (Device ID) for the AXB-DMX512.
    The DIP Switch to the right of the DEVICE DIP is
    reserved - no settings are required.
    Rear panel components:
    DMXIN port 5-wire, captive-wire connector for receiving data.
    DMXOUT port 5-wire, captive-wire connector for transmitting data.
    AXlink 4-wire, captive-wire connector for data and power.
    Dimensions (HWD) 1.5" x 5.5" x 5.5" (38 mm x 140 mm x 140 mm)
    Enclosure Metal with black matte finish
    Mounting Rack mounting with the optional AC-RK Accessory Rack
    Kit
    Weight 1.1 lb (0.5 kg)
    Device DIP Switch Settings
    Position 12345678
    Value 1 2 4 8 16 32 64 128
    AXlink
    DEVICE
    ON
    RXTX
    Device ID DIP Switch
    Axlink activity LED
    DMX512 (Transmit) LED
    DMX512 (Receive) LED
    FIG. 2 Location of termination jumpers (JP4-JP5)
    FIG. 3 Termination jumper pin settings for JP4 and JP5
    FIG. 4 AXB-DMX512 (rear view)
    COR
    JP5
    JP4
    front
    Termination Jumpers
    (JP4 / JP5)
    DEVICE DIP Switch
    The DIP Switch located to the
    right of the DEVICE DIP switch
    is not used - no settings are
    required, and any setting
    will work.
    TERM
    HIZ
    IN OUT AXlink
    DATA
    GND
    GND
    DATA
    DATA
    DATA
    NC
    DATA
    DATA
    DATA
    DATA
    NC
    GND
    AXP
    AXM
    PWR
    1
    2
    1
    2
    1
    1
    2
    2
AMX AXB-DMX512

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om AMX AXB-DMX512? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av AMX AXB-DMX512 att svara på din fråga.

Se manualen för AMX AXB-DMX512 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 8.7. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om AMX AXB-DMX512? Ställ din fråga här

AMX AXB-DMX512 – specifikationer

Allmänt
Varumärke AMX
Modell AXB-DMX512
Produkt Controller
EAN 718878008706, 7188780087060
Språk Engelsk
Filtyp PDF
Tekniska data
Produktstorlek (BxDxH) 141 x 138.4 x 38.4
Vikt 499

Vanliga frågor

Nedan hittar du de vanligaste frågorna om AMX AXB-DMX512 .

Är din fråga inte listad? Ställ din fråga här

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer