Anthro AnthroBench bruksanvisning

Anthro AnthroBench
(1)
  • Sidantal: 2
  • Filtyp: PDF
TECHNOLOGY FURNITURE
®
0148” Wide Bench Shelf ...........Qty. 1 ..................(see below)
28” Deep
(S4829zz/xx & S4835zz/xx) ..............100-6406-00
36” Deep
(B4829zz/xx & B4835zz/xx) .............100-6349-00
02– Bench Leg Assemblies ...........Qty. 2 ..................(see below)
25” Bench Legs
(S4829zz/xx & S4835zz/xx) ..835-5008-00
31” Bench Legs
(B4829zz/xx & B4835zz/xx) 835-5009-00
03– Bench Arm Left .......................Qty. 1 .............
225-5357-00
04– Cross Ends ................................Qty. 2 ............
225-5334-00
05– 1
1
/
4
Wood Screws .................Qty. 12 ...........325-5178-00
06– Glide Insert Screws ...............Qty. 4 .............
325-5052-00
07– 2.5” End Caps ..........................Qty. 4 ............
175-5158-00
08– Glide Inserts .............................Qty. 4 .............
525-5030-00
09– Glides (
1
/
2
-13 X 2”) ................Qty. 4 ...........325-5165-00*
10– Cap Screws (
5
/
16
-18 X 4”) ...Qty. 8 .............325-5166-00
11– Curved Washers .....................Qty. 8 .
225-2050-00 or 225-3522-00
12– Bench Base Tubes ...................Qty. 2 ..................(see below)
28” Deep
(S4829zz/xx & S4835zz/xx) ..............125-5225-00
36” Deep
(B4829zz/xx & B4835zz/xx) .............125-5183-00
Enclosed Parts List
Detailed views of all Hardware is provided with each Assembly Step
13– 15” Bench Buttress ................Qty. 2 .............
225-5386-00
14– 41.5” Bench Cross Tubes ....Qty. 2 .............
125-5184-00
15– Keps Nuts (
1
/
4
-20) ..................Qty. 8 .............325-5130-03
16– Pan Screws (
1
/
4
-20 X .5”) ....Qty. 8 ............. 325-5003-00
17– Bench Arm Right .....................Qty. 1 .............
225-5358-00
18– Support Screws .......................Qty. 20 ...........
325-5010-00
19– 48” Bench Pans .......................Qty. 2 .............
225-5370-00
All Screw quantities listed here are the minimum needed
for your Bench assembly. There may be a few extra
Screws included, which are not counted in the Parts List.
To make the assembly of your Anthro Bench even easier, we
have included the required tools.. The handy Hex Driver Bit
can be used in your electric drill in place of the Hex Driver.
20- Hex Driver
5
/
32
.......................Qty. 1 .............375-5000-00
21- Hex Driver Bit
5
/
32
................Qty. 1 .............375-5003-00
22- Hex Key
1
/
4
..............................Qty. 1 .............375-5024-00
3-Way Wrench
(not shown) ..............Qty. 1 .............225-5196-03
Anthro
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062
SAVE THESE INSTRUCTIONS!
anthro.com
September 2004 Rev. E
These Assembly Instructions are for the 48” AnthroBench models: B4829zz/xx, S4829zz/xx, B4835zz/xx
& S4835zz/xx. Before beginning assembly of your AnthroBench, please take a moment to review the parts listed below
to verify that your shipment is complete.
04
06
07
03
02
09
05
08
01
10
13
11
14
12
15
16
17
18
19

48” AnthroBench

Assembly Instructions

Does your Bench have 5” Casters?*
(If you purchased a 640RT - your Caster Part
Numbers are given here.)
5” Locking Caster
150-5024-00
5” Non-Locking Caster
150-5025-00
Your AnthroBench is heavy!
A second person will make this
assembly procedure much easier.

Step 7

Place the Bench Shelf (laminate facing down) onto the
floor.
With the help of another person, carefully rotate the Leg
Assembly (from Step 6) over onto the Shelf.
Position the holes on the Pans and Arms to align with the
twelve predrilled holes on the Shelf. Insert two Wood
Screws through each center opening of the Bench Pans
(shown encircled at right).
Install the remaining Wood Screws into each of the Arms
and Pans, a total of twelve Wood Screws will be installed.
In preparation for Step 8, carefully rotate your Anthro-
Bench back over onto the Glides.

Step 8 (requires a 3-Way Wrench)

FIRST- from the rear of your Bench, align one Buttress
with one hole on the Back Pan. Install a Pan Screw
through the Buttress and loosely capture using a Keps Nut
on the opposite side.
SECOND- position one Cross End on the remaining
Buttress end and install a Pan Screw and Keps Nut in the
same manner, but do not fully tighten.
THIRD- rotate the Buttress to align the Cross End with
two openings on the Leg. Secure the Cross End to the
Leg using two Support Screws.
Repeat this entire procedure for the remaining Buttress
and Cross End on the opposite end.
Tighten all Pan Screws, Support Screws & Keps Nuts.
Congratulations! Your 48” AnthroBench assembly is
complete. Please return the enclosed Registration Card to
receive our product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
Questions? 1-800-325-3841
1
1
/
4
Wood Screw
325-5178-00
(
1
/
4
-20 X .5”) Pan Screw
325-5003-00
(
1
/
4
-20) Keps Nut
325-5130-03
Buttress
Back Pan hole
Support Screw
325-5010-00
FIRST Install this Pan Screw
SECOND Install this Pan Screw
THIRD Install the Cross End
Lower Metal Mounts
Cable Grommet
Workstation Screw
(not counted in Parts List)
325-5092-00
Removal of Leg Covers & Cable Grommets
Remove the Leg Cover by: 1. First removing the top two
Workstation Screws. 2. Slightly lift the Cover upward and
off the lower metal mounts.
Cable Grommets are snapped into and out of each of the
circular Leg openings.
NOTE: The purpose of the Buttress is not to
support your Bench Shelf. It is intended to make
your Bench absolutely rigid under extreme weight
conditions.
Pans
Arms
Rounded Edge of Shelf
Predrilled holes
22
21
20
Anthro AnthroBench

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Anthro AnthroBench? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Anthro AnthroBench att svara på din fråga.

Se manualen för Anthro AnthroBench helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 8.9. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Anthro AnthroBench? Ställ din fråga här

Anthro AnthroBench – specifikationer

Allmänt
Varumärke Anthro
Modell AnthroBench
Produkt Skrivbord
Språk Engelsk
Filtyp PDF
Vikt & dimension
Bredd 1219.2 mm
Djup 914.4 mm
Höjd 889 mm
Design
Produktens färg Svart
Maxvikt 181.4 kg
visa mer

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Anthro AnthroBench .

Är din fråga inte listad? Ställ din fråga här