Be Quiet! Dark Rock 4 bruksanvisning

Be Quiet! Dark Rock 4
(1)
  • Sidantal: 2
  • Filtyp: PDF
  • Mounting the CPU cooler

    First remove the protective foil from the underside of the

    cooler. Spread the thermal paste (16) on the surface of the

    CPU. The amount supplied is sufficient for one or two

    applications.

    Caution: The thermal paste supplied is not suitable for human

    consumption. If swallowed, drink lots of water and urgently

    seek medical attention. Keep it out of the reach of children.

    Avoid contact with skin and eyes.

    Position the cooler mounting bridge (6) centrally on the cooler

    (1). Next place the cooler unit onto the CPU. Insert the Intel/

    AMD mounting bridge fastening screws (11) from above into

    the cooler mounting bridge (6) and then screw these alternately

    tight. You can use the cross-tip screwdriver (15) for this.

    Mount the 135mm fan (2) onto the cooler unit (1) using the

    fan clips (17). Connect the fan to the motherboard’s PWM

    signal.

    When dismantling the 135mm fan (2) push the notches of the

    fan clips (17) away from the fan.

    Position the cooler mounting bridge (6) centrally on the cooler.

    Next place the cooler (1) unit onto the CPU. Insert the Intel/

    AMD mounting bridge fastening screws (11) from above into

    the cooler mounting bridge (6) and then screw these alternately

    tight. You can use the cross-tip screwdriver (15) for this.

    Fasten the 135mm fan (2) onto the cooler unit (1) using fan

    clips (17). Connect the fan to the motherboard’s PWM

    signal.

    When dismantling the 135mm fan (2), push the notches of

    the fan clips (17) away from the fan.

    Introduction: Thank you for deciding to purchase a be quiet!

    product. The following instructions will guide you through the

    installation process. If you do encounter installation problems,

    please don't hesitate to contact our customer services by

    mailing service@bequiet.com. Please note that be quiet!

    cannot accept liability for damage caused by compatibility

    problems.

    Warranty:

    3 years manufacturer guarantee for consumers (original

    purchase from authorized be quiet! dealers only)

    Guarantee work can only be processed with an included

    copy of the purchase receipt from an authorized be quiet!

    dealer

    Manipulation and structural changes of any kind as well

    as damages through external mechanical forces lead to a

    complete voiding of the guarantee

    Our General Warranty Conditions apply, which can be

    viewed on bequiet.com

    Listan GmbH & Co.KG . Biedenkamp 3a . 21509 Glinde

    Germany

    For further information contact us via e-mail:

    service@bequiet.com

    SCOPE OF DELIVERY

    General

    We recommend preparatory mounting of the

    cooler outside the PC case for subsequent

    installation.

    The following parts are needed for this:

    1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 2x Intel

    mounting brackets (4), 1x cooler mounting bridge (6), 4x Intel

    spacer nuts (7), 4x mounting bracket fastening screws (10), 2x

    Intel/AMD mounting bridge fastening screws (11), 1x cross-tip

    screwdriver (15) 1x thermal paste (16), 2x fan clips (17)

    Assembly of the cooler mounting frame

    First screw the Intel spacer nuts (7) onto the threads of the

    socket frame. Place the Intel mounting brackets (4) over the

    Intel spacer nuts and screw these tight with the mounting

    bracket fastening screws (10). You can use the cross-tip

    screwdriver (15) for this.

    Mounting the CPU cooler

    First remove the protective foil from the underside of the cooler.

    Spread the thermal paste (16) on the surface of the CPU. The

    amount supplied is sufficient for one or two applications.

    Caution: The thermal paste supplied is not suitable for

    human consumption. If swallowed, drink lots of water and

    urgently seek medical attention. Keep it out of the reach of

    children. Avoid contact with skin and eyes.

    Installation video
    1366, 2011(-3) square ILM, 2066
    1150, 1151, 1155, 1156

    General

    We recommend preparatory mounting of the

    cooler outside the PC case for subsequent

    installation.

    The following parts are needed for this:

    1x Dark Rock 4 CPU cooler (1), 1x 135mm fan (2), 1x Intel

    backplate (3), 2x Intel mounting brackets (4), 1x cooler mounting

    bridge (6), 4x Intel 115X/1366 nuts (8), 4x mounting bracket

    fastening screws (10), 2x Intel/AMD mounting bridge fastening

    screws (11), 4x Intel backplate screws (12), 4x O-rings (14), 1x

    cross-tip screwdriver (15), 1x thermal paste (16), 2x fan clips (17)

    Mounting the backplate

    Position the Intel backplate screws (12) in the notches situated

    on the rear side of the Intel backplate (3). Pay attention in so

    doing to align with the holes drilled for each socket.

    For fixing the backplate screws onto the Intel backplate use

    the O-rings (14). Once assembly of the Intel backplate for the

    respective Intel socket is complete, position it under the

    motherboard. Make sure that the backplate screws are

    precisely positioned inside the motherboard holes.

    Installation of the mounting brackets

    Screw the Intel 115X/1366 nuts (8) onto the previously

    positioned Intel backplate (3). Then position the Intel mounting

    brackets (4) over the Intel 115X/1366 nuts (8) and affix these

    with the mounting bracket fastening screws (10). You can use

    the cross-tip screwdriver for this (15).

    1366, 2011(-3) square ILM, 2066
    1150, 1151, 1155, 1156
    1366
    1150, 1151,
    1155, 1156
    Intel LGA 2011(-3) square ILM / LGA 2066
    Intel LGA 1150 / 1151 / 1155 / 1156 / 1366
    We recommend removal of the cooler prior to transportation.

    January 2018

    !

    Part name Quantity

    be quiet! Dark Rock 4 cooler 1

    135mm fan 1

    Intel backplate 1

    Intel mounting brackets 2

    Long AMD mounting brackets 2

    Cooler mounting bridge 1

    Intel spacer nuts 4

    Intel 115X/1366 nuts 4

    Part name Quantity

    AMD spacer nuts 4

    Mounting bracket fastening

    screws

    4

    Intel/AMD mounting bridge

    fastening screws

    2

    Intel backplate screws 4

    AMD backplate screws 4

    O-rings 4

    Cross-tip screwdriver 1

    Thermal paste 1

    Fan clips 2

    AM3 washers 4

    2
    3
    4
    5
    6
    7
    8
    9
    10
    11
    12
    13
    14
    15
    16
    17
    Installation video
Be Quiet! Dark Rock 4

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Be Quiet! Dark Rock 4? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Be Quiet! Dark Rock 4 att svara på din fråga.

Se manualen för Be Quiet! Dark Rock 4 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 9.6. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Be Quiet! Dark Rock 4? Ställ din fråga här

Be Quiet! Dark Rock 4 – specifikationer

Allmänt
Varumärke Be Quiet!
Modell Dark Rock 4
Produkt CPU-kylare
Språk Engelsk
Filtyp PDF
Vikt & dimension
Vikt 920 g
Bredd 136 mm
Djup 159.4 mm
Höjd 74.3 mm
Diameter på värmerör 6 mm
Mått, fläkt (B x D x H) 135 x 135 x 22 mm
Kabellängd 0.22 m
Förpackningens bredd 205 mm
Höjd 214 mm
Låddjup 149 mm
Vikt inkl. förpackning 1170 g
Strömtillförsel
Värmeavledningseffekt (TDP) 200 W
Uppmätt spänning 12 V
Uppskattad strömförbrukning 0.11 A
Strömförsörjning 1.32 W
Prestanda
Stödd processor uttag LGA 1150 (Socket H3),LGA 1151 (Socket H4),LGA 1155 (Socket H2),LGA 1156 (Socket H),LGA 1200 (Socket H5),LGA 1366 (Socket B),LGA 2011 (Socket R),LGA 2011-v3 (Socket R),LGA 2066,Socket AM2,Socket AM2+,Socket AM3,Socket AM3+,Socket AM4,Socket FM1,Socket FM2,Socket FM2+
Fläktdiameter 135 mm
Stöd för pulsbreddsmodulering (PWM) Ja
Ljudnivå (låg hastighet) 10.5 dB
Ljudnivå (hög hastighet) 21.4 dB
Rotationshastighet (max) 1400 RPM
Lämplig för Processor
Lagertyp Fluid Dynamic Bearing (FDB)
Modell Kylare
Kompatibla processorer -
Design
Antal fläktar 1 fläkt/-ar
Antal fenor 51
Fläktbladens material Gjuten aluminium
Material Koppar
Antal värmerör 6
Produktens färg Svart
Fan kontakt 4-stift
Förpackningens innehåll
Skruvar medföljer Ja
Tekniska data
Hållbarhetscertifiering RoHS
Övrigt
Stöd för extra fläktar Ja