Be Quiet! Dark Rock Pro 4 bruksanvisning

Be Quiet! Dark Rock Pro 4
(2)
  • Sidantal: 2
  • Filtyp: PDF
  • First remove the protective foil from the underside of the cooler.

    Spread the thermal paste (17) on the surface of the CPU. The

    amount supplied is sufficient for one or two applications.

    Caution: The thermal paste supplied is not suitable for human

    consumption. If swallowed, drink lots of water and urgently

    seek medical attention. Keep it out of the reach of children.

    Avoid contact with skin and eyes.

    Position the cooler mounting bridge (7) centrally on the cooler.

    Next place the cooler unit over the CPU. Loosen both heatpipe

    caps that are found in the middle of the top side of the cooler.

    Insert the Intel/AMD mounting bridge fastening screws (12)

    from above into the cooler mounting bridge and then screw

    these alternately tight.

    You can use the cross-tip screwdriver (16) for this.

    Subsequently retighten both heatpipe caps on the top side of

    the cooler.

    Fasten the 120mm fan (3) using fan clips (18) onto the front

    side of the cooler. Slide the 135mm fan (2) between the two

    heatsinks and also fasten this with fan clips (18). Connect

    both fans using the the Y cable (20). Connect this to the

    CPU fan connector on the motherboard.

    When dismantling the fans, push the notches of the fan

    clips (18) away from the fan.

    Position the cooler mounting bridge (7) centrally on the cooler

    (1). Next place the cooler unit over the CPU. Loosen both

    heatpipe caps that are found in the middle of the topside of the

    cooler (rotate as illustrated). Insert the Intel/AMD mounting

    bridge fastening screws (12) from above into the cooler

    mounting bridge (7) and then screw these alternately tight. You

    can use the cross-tip screwdriver (16) for this.

    Subsequently retighten both heatpipe caps on the top side of

    the cooler.

    Fasten the 120mm fan (3) using fan clips (18) onto the front

    side of the cooler. Slide the 135mm fan (2) between the two

    heatsinks and also fasten this with fan clips (18). Connect

    both fans using the the Y cable (20). Connect this to the

    CPU fan connector on the motherboard.

    When dismantling the fans, push the notches of the fan

    clips (18) away from the fan.

    Introduction: Thank you for deciding to purchase a be quiet!

    product. The following instructions will guide you through the

    installation process. If you do encounter installation problems,

    please don't hesitate to contact our customer services by

    mailing service@bequiet.com. Please note that be quiet!

    cannot accept liability for damage caused by compatibility

    problems.

    Warranty:

    3 years manufacturer guarantee for consumers (original

    purchase from authorized be quiet! dealers only)

    Guarantee work can only be processed with an included

    copy of the purchase receipt from an authorized be quiet!

    dealer

    Manipulation and structural changes of any kind as well

    as damages through external mechanical forces lead to a

    complete voiding of the guarantee

    Our General Warranty Conditions apply, which can be

    viewed on bequiet.com

    Listan GmbH & Co.KG . Biedenkamp 3a . 21509 Glinde

    Germany

    For further information contact us via e-mail:

    service@bequiet.com

    SCOPE OF DELIVERY

    General

    We recommend preparatory mounting of the

    cooler outside the PC case for subsequent

    installation.

    The following parts are needed for this:

    1x Dark Rock Pro 4 CPU cooler (1), 1x 135mm fan (2), 1x 120mm

    fan (3), 2x Intel mounting brackets (5), 1x cooler mounting

    bridge (7), 4x Intel spacer nuts (8), 4x mounting bracket

    fastening screws (11), Intel/AMD mounting bridge fastening

    screws (12), 1x cross-tip screwdriver (16), 1x thermal paste

    (17), 4x fan clips (18), 1x Y cable (20)

    Assembly of the cooler mounting frame

    First screw the Intel spacer nuts (8) onto the threads of the

    socket frame. Place the Intel mounting brackets (5) over the

    Intel spacer nuts and screw these tight with the mounting

    bracket fastening screws (11). You can use the cross-tip

    screwdriver (16) for this.

    First remove the protective foil from the underside of the cooler.

    Spread the thermal paste (17) on the surface of the CPU. The

    amount supplied is sufficient for one or two applications.

    Caution: The thermal paste supplied is not suitable for

    human consumption. If swallowed, drink lots of water and

    urgently seek medical attention. Keep it out of the reach of

    children. Avoid contact with skin and eyes.

    Installation video
    1366, 2011(-3) square ILM, 2066
    1150, 1151, 1155, 1156

    General

    We recommend preparatory mounting of the

    cooler outside the PC case for subsequent

    installation.

    The following parts are needed for this:

    1x Dark Rock Pro 4 CPU cooler (1), 1x 135mm fan (2), 1x 120mm

    fan (3), 1x Intel backplate (4), 2x Intel mounting brackets (5),

    1x cooler mounting bridge (7), 4x Intel 115X/1366 nuts (9), 4x

    mounting bracket fastening screws (11), 2x Intel/AMD mounting

    bridge fastening screws (12), 4x Intel backplate screws (13), 4x

    O-rings (15), 1x cross-tip screwdriver (16), 1x thermal paste (17),

    4x fan clips (18), 1x Y cable (20)

    Mounting the backplate

    Position the Intel backplate screws (13) in the notches situated

    on the rear side of the Intel backplate (4). Pay attention in so

    doing to align with the holes specially drilled for each socket.

    For fixing the backplate screws onto the Intel backplate use

    the O-rings (15). Once assembly of the Intel backplate for the

    respective Intel socket is complete, position it under the

    motherboard. In so doing make sure that the Intel backplate

    screws (13) are precisely positioned inside the motherboard

    holes.

    Assembly of the cooler mounting frame

    Screw the Intel 115X/1366 nuts (9) onto the previously

    positioned Intel backplate (4). Then position the Intel mounting

    brackets (5) over the Intel 115X/1366 nuts and affix these with

    the mounting bracket fastening screws (11). You can use the

    cross-tip screwdriver for this (16).

    1366, 2011(-3) square ILM, 2066
    1150, 1151, 1155, 1156
    Intel LGA 2011(-3) square ILM / LGA 2066
    Intel LGA 1150 / 1151 / 1155 / 1156 / 1366
    We recommend removal of the cooler prior to transportation.

    January 2018

    !

    Part name Quantity

    be quiet! Dark Rock Pro 4 cooler 1

    135mm fan 1

    120mm fan 1

    Intel backplate 1

    Intel mounting brackets 2

    Short AMD mounting brackets 2

    Cooler mounting bridge 1

    Intel spacer nuts 4

    Intel 115X/1366 nuts 4

    Part name Quantity

    AMD spacer nuts 4

    Mounting bracket fastening

    screws

    4

    Intel/AMD mounting bridge

    fastening screws

    2

    Intel backplate screws 4

    AMD backplate screws 4

    O-rings 4

    Cross-tip screwdriver 1

    Thermal paste 1

    Fan clips 2

    AM3 washers 4

    Y cable 1

    2
    3
    4
    5
    6
    7
    8
    9
    10
    11
    12
    13
    14
    15
    16
    17
    18
    19
    20
    Installation video
    1366
    1150, 1151,
    1155, 1156
Be Quiet! Dark Rock Pro 4

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Be Quiet! Dark Rock Pro 4? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Be Quiet! Dark Rock Pro 4 att svara på din fråga.

Se manualen för Be Quiet! Dark Rock Pro 4 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 2 personer med ett genomsnitt på 8.7. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Be Quiet! Dark Rock Pro 4? Ställ din fråga här

Be Quiet! Dark Rock Pro 4 – specifikationer

Allmänt
Varumärke Be Quiet!
Modell Dark Rock Pro 4
Produkt CPU-kylare
Språk Engelsk
Filtyp PDF
Prestanda
Fläktdiameter 120/135 mm
Lämplig för Processor
Modell Kylare
Kompatibla processorer -
Stödd processor uttag LGA 1150 (Socket H3),LGA 1151 (Socket H4),LGA 1155 (Socket H2),LGA 1156 (Socket H),LGA 1200 (Socket H5),LGA 1366 (Socket B),LGA 2011 (Socket R),LGA 2011-v3 (Socket R),LGA 2066,Socket AM2,Socket AM2+,Socket AM3,Socket AM3+,Socket AM4,Socket FM1,Socket FM2,Socket FM2+
Rotationshastighet (max) 1500 RPM
Ljudnivå (hög hastighet) 24.3 dB
Ljudnivå (låg hastighet) 12.8 dB
Stöd för pulsbreddsmodulering (PWM) Ja
Lagertyp Fluid Dynamic Bearing (FDB)
Vikt & dimension
Diameter på värmerör 6 mm
Vikt 1130 g
Mått, fläkt (B x D x H) 135 x 135 x 22 mm
Bredd 136 mm
Djup 162.8 mm
Höjd 123.7 mm
Förpackningens bredd 205 mm
Låddjup 181 mm
Höjd 212 mm
Vikt inkl. förpackning 1390 g
Kabellängd 0.22 m
Design
Antal värmerör 7
Fläktbladens material Gjuten aluminium
Antal fläktar 2 fläkt/-ar
Antal fenor 90
Fan kontakt 4-stift
Produktens färg Svart
Material Koppar
Strömtillförsel
Värmeavledningseffekt (TDP) 250 W
Uppmätt spänning 12 V
Uppskattad strömförbrukning 0.16 A
Strömförsörjning 1.92 W
Tekniska data
Hållbarhetscertifiering RoHS
Förpackningens innehåll
Skruvar medföljer Ja
Övrigt
Stöd för extra fläktar Ja