Brother P-Touch 2430PC

Brother P-Touch 2430PC bruksanvisning

(1)
  • ELECTRONIC L
    ELECTRONIC L
    ABELING SYSTEM
    ABELING SYSTEM
    ELECTRONIC LABELING SYSTEM
    USER’S GUIDE
    USER’S GUIDE
    English
    Printed in China
    LW5545001
    www.brother.com
    *Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States
    and other countries.
    *The name of other software or products used in this document are trademarks or registered trademarks of the
    respective companies that developed them.
    INTRODUCTION
    Thank you for choosing the PT-2430PC. Your new P-touch labeler uses P-touch Editor Lite software, which is already installed on your labeler.
    There is no need to install any software or drivers onto your PC in order to make creative labels. This manual includes important precautionary
    information and simple instructions for operating your new P-touch labeler. Be sure to read the instructions before use and use the product in ac-
    cordance with these instructions. Keep this manual handy for future reference. If new versions of the PT-2430PC software become available, this
    manual may not re ect the updated features. Therefore, you may nd that the software and the contents in this guide are different.
    Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
    Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA
    TEL: (908) 704-1700
    declares that the product: Product Name: P-touch Labeler PT-2430PC
    Model Number: PT-2430PC
    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
    interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
    This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
    limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
    can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
    communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
    interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor-
    rect the interference by one or more of the following measures:
    -
    Reorient or relocate the receiving antenna.
    -
    Increase the separation between the equipment and receiver.
    -
    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    -
    Consult the dealer or an experienced radio/TV technician for help.
    -
    Changes or modi cations not expressly approved by Brother Industries, Ltd. could void the user’s authority to operate the equipment.
    -
    The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital device.
    SAFETY PRECAUTIONS
    WARNING
    CAUTION
    General Precautions
    Always use the speci ed voltage and the included AC adapter (AD-24ES) for this machine to prevent any damage or failure.
    Unplug the power cord immediately and stop using the P-touch labeler during an electrical storm. There may be a remote risk of electric shock from lightning.
    Do not use the AC adapter in places of high humidity such as bathrooms.
    Do not overload the power cord.
    • Do not place heavy objects on, or damage the power cord or plug. Do not forcibly bend or pull the power cord. When disconnecting the power cord from the power outlet, al-
    ways hold the plug.
    • To prevent re or electric shock, make sure that the plug is fully inserted to the power outlet. Do not use an outlet that is loose.
    Do not get the machine/AC adapter/power plug wet, such as by handling them with wet hands or spilling beverages on to them.
    Do not disassemble or modify P-touch labeler/AC adapter/batteries.
    Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the batteries.
    Do not throw into re or heat up the battery.
    Disconnect the AC adapter, remove batteries and stop using immediately if you notice any abnormal odor, heat, discoloration, deformation or anything unusual while in use, or
    in storage.
    To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the print head.
    Remove the batteries and disconnect the AC adapter if you do not intend to use P-touch labeler for an extended period of time.
    • Do not use old and new batteries together or mix alkaline batteries with other type batteries, or set the positive and negative end in the wrong position. Otherwise, the batter-
    ies may leak or be damaged.
    To prevent damage or breakage, do not drop or hit P-touch labeler/AC adapter.
    Use only the USB cable included with the P-touch labeler.
    • Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the color of the label may change or be transferred to other
    objects. Before applying the label, check the environmental condition and the material.
    Do not use the P-touch labeler in any way or for any purpose not described in this guide. Doing so may result in accidents or damage the machine.
    Use only Brother TZ tapes with this machine. Do not use tapes that do not have the
    mark.
    Do not clean P-touch labeler with alcohol or other organic solvents. Only use a soft, dry cloth.
    Do not touch the print head with your ngers anytime to prevent from a burn. Use a soft wipe (e.g. a cotton swab) when cleaning the print head.
    Do not put any foreign objects into the tape exit slot or AC adapter connector, etc.
    Do not place the P-touch labeler/battery in direct sunlight or rain, near heaters or other hot appliances, in any location exposed to extremely high or low temperatures (e.g. on
    the dashboard or in the back of your car), high humidity, or dusty locations.
    Do not try to print labels using an empty tape cassette in the P-touch labeler. Doing so will damage the print head.
    Do not pull the tape being fed from the P-touch labeler, otherwise the tape cassette or P-touch labeler may be damaged.
    Insert a tape
    cassette.
    Close the cassette
    cover.
    Verify that the P-touch labeler is
    turned off. Open the cassette cover
    as shown by the arrow in the above
    illustration while pressing the part
    marked "<<".
    Insert a tape cassette as shown in
    the above illustration.
    Make sure that the end of the tape feeds under the tape guides.
    • If the ink ribbon is loose, use your nger to wind the toothed
    wheel in the direction of the arrow on the cassette.
    Use only Brother tapes with the P-touch labeler.
    For initial use of the tape, install the tape. Then, push in the Feed
    & Cut button to cut the tape.
    Make sure that the release lever is up when closing the tape cover.
    The tape cover cannot be closed if the release lever is pressed down.
    Connect the P-touch labeler's power supply.
    When using the included AC adapter (AD-
    24ES), insert the plug on the adapter cord
    into the adapter jack on the bottom end of the
    P-touch labeler. Insert the plug into the near-
    est standard electrical outlet.
    Auto Power Off Function
    When the P-touch labeler is operating on battery power only,
    it will turn off automatically if not used for a period of 20 min-
    utes. The message “Unsafe Removal of Device” may be
    displayed depending on the Operating System running on
    your PC. Any data being displayed will be saved. When you
    turn the labeler back on, click on the Editor Lite icon to re-
    sume creating your label.
    Connect the USB cable and start P-touch Editor Lite.
    When using
    Windows Vista
    ®
    When connecting the device for the rst time, perform the
    scan and then select the Always do this for software and
    games check box on the dialog box displayed when the
    scan completes. P-touch Editor Lite will start automatically
    the next time you connect the P-touch labeler.
    How to disconnect the P-touch
    labeler
    If you would like to use the more advanced software that is available for your P-touch labeler,
    you are able to install P-touch Editor 5.0 from the included CD-ROM. This advanced software
    will give you greater label making functionality.
    Do not connect the P-touch labeler to your PC before you begin the P-touch Edi-
    tor 5.0 installation. For details on how to install P-touch Editor 5.0, see the in-
    stallation guide in the included CD-ROM.
    Starting P-touch Editor 5.0
    Review the names of P-touch labeler parts.
    Install a tape cassette.
    The PT-2430PC has 2 mode selector settings - “EL” and “E”. The mode selector
    switch is pre-set at the factory to the EL mode, for use with P-touch Editor Lite. For
    E mode, you will need to install P-touch Editor 5.0, a more advanced labeling soft-
    ware, and the required drivers from the enclosed CD. For details on how to install
    the P-touch Editor 5.0, see “Starting P-touch Editor 5.0” below.
    Connect the
    USB cable.
    Turn on the P-touch labeler.
    The LED lamp will light up.
    For details on using
    P-touch Editor Lite,
    see the back of this
    sheet.
    P-touch Editor Lite
    starts immediately.
    Click Open folder to
    view les.
    Exit P-touch Editor Lite by clicking on the at the top
    right.
    To disconnect the labeler, click the icon in the computer’s
    task bar (
    , , or ).
    Click Safely remove USB Mass Storage Device.
    When The device can be safely removed is displayed,
    turn off the P-touch labeler and disconnect the USB ca-
    ble.
    It will take longer
    than usual to
    start P-touch Editor
    Lite when connecting
    P-touch labeler to
    your computer for the
    first time. If the soft-
    ware does not start
    automatically when
    you connect the ma-
    chine, you may
    launch it from My
    Computer. Start
    P-touch Editor Lite by
    double-clicking
    PTLITE10.EXE.
    Open the cassette
    cover.
    Do not turn off the power or remove the labeler while
    using P-touch Editor Lite.
    When using the P-touch labeler with
    batteries, insert six new AA alkaline
    batteries (LR6), making sure that
    their poles point in the correct direc-
    tions. Always replace all six batter-
    ies at the same time using brand
    new ones.
    Move the mode selector
    switch on the back of the
    P-touch labeler to the “E”
    position before connecting
    the USB cable.
    Getting Ready
    The follow-
    ing screens
    may differ
    depending on
    the Operating
    System on
    your PC.
    Double-click PTLITE10
    .
    LED lamp
    Power
    button
    Tape exit slot
    AC adapter (included)
    connecter
    Mode selector
    switch
    USB port
    Print head
    Tape cutter
    Click P-touch Editor Lite.
    Feed & Cut button
    Release Lever
    International ENERGY STAR
    ®
    Compliance Statement
    The purpose of the International ENERGY STAR
    ®
    Program is to
    promote the development and popularization of energy-ef cient of-
    ce equipment.
    As an ENERGY STAR
    ®
    Partner, Brother Industries, Ltd. has deter-
    mined that this product meets the ENERGY STAR
    ®
    guidelines for
    energy ef ciency.
    LW5545001_US-ENG.indd 1LW5545001_US-ENG.indd 1 3/18/2010 9:49:38 AM3/18/2010 9:49:38 AM
Brother P-Touch 2430PC

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Brother P-Touch 2430PC? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Brother P-Touch 2430PC att svara på din fråga.

Se manualen för Brother P-Touch 2430PC helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 9.5. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Brother P-Touch 2430PC? Ställ din fråga här

Brother P-Touch 2430PC – specifikationer

Allmänt
Varumärke Brother
Modell P-Touch 2430PC
Produkt Etikettskrivare
EAN 12502621126, 4977766663014, 4977766663045, 4977766664417, 4977766664431, 4977766664455, 4977766664479, 4977766705288, 777780148825, 777780462730
Språk Engelsk
Filtyp PDF
Utskriftshastighet
Maximal upplösning 180 x 180
Vertikal utskrift
Skrivhastighet 10
Anslutningar
PC-ansluten
Standardgränssnitt USB 2.0
Vikt & dimension
Bredd 66
Djup 188
Höjd 112
Vikt 600
Strömtillförsel
Antal batterier 6
Batterityp AA
null
Systemkrav
Mac-kompatibel
Kompatibla operativsystem Microsoft Windows 2000 Professional / XP / Vista
Prestanda
Bandtyp TZ
Tapeklippning Automatisk
Antal stilar 6
Förpackningens innehåll
Medföljande programvara P-touch Editor 5.0
Design
Produktens färg Vit
Övrigt
Bandstorlekt 3.5
Pappershantering
Maximal etikettbredd 24

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Brother P-Touch 2430PC .

Är din fråga inte listad? Ställ din fråga här

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer