CDA TF10CH bruksanvisning

  • For Service & Technical Support Call: 01949 862012
    Fax: 01949 862003
    TF10 - Single lever filter tap
    5 Year warranty:
    In the unlikely event that you should experience any defect in the materials or workmanship of your new CDA mixer within FIVE years of
    purchase, the purchaser’s sole remedy shall be the replacement (at the manufacturer’s discretion) of all or any part of the product that is
    defective. All working parts and valves are guaranteed for a period of TWO years from purchase. Decorative surface finishes and O-rings
    are guaranteed for ONE year from the date of purchase provided that our advice concerning care has been observed. This is provided that
    the mixer has been used for normal domestic purposes in the UK and that the care, installation and maintenance instructions have been
    observed. The warranty extends to the original purchaser only. You should retain a copy of your dated invoice as proof of purchase to
    validate any claims under this guarantee.
    Care Instructions for your Kitchen Sink Mixer:
    To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean, soft damp cloth. A solution of warm water and
    a mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly and wiped dry. Any other cleaning action will
    invalidate your warranty. If the tap has a diffuser it should be cleaned periodically.
    Abrasive cleaners, scouring cleaners and acidic cleaners must not be used under any circumstances. Avoid contact with all solvents
    (including chlorinated solvents, ketones or acetones as these may result in surface deterioration or etching). Also avoid contact with any
    harsh household chemicals such as oven cleaners, drain cleaners, rust removers, paint strippers and toilet bowl cleaners, bar keepers friend
    or Brasso.
    Important Technical Data:
    Minimum hot / cold operating pressure 0.5 / 1.0 bar Maximum hot water temperature 70°C*
    Maximum operating pressure 5.5 bar* Recommended hot water temperature 46°C
    *If these temperatures or pressures are exceeded, even for short periods, damage can result.
    CDA taps are either WRAS approved or manufactured in accordance with recognised European standards. Please ensure that your
    Kitchen mixer is fitted in accordance with Local Water Byelaws.
    These installation guidelines have been prepared for your direction and you must exercise due care at all times. We do not accept
    responsibility for problems that may occur through improper installation. Whilst assembling the tap take care not to accidentally loosen any
    screwed assemblies.
    Installation Preparation:
    Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any remaining
    solder, swarf or impurities from your system. Failure to carry out this simple procedure could cause problems or damage to the workings of
    the mixertap.
    We strongly recommend installing particle filter strainers and isolation valves to both the hot and cold feed pipes in an accessible position.
    This will help to prevent premature failure of the valves and ease any future maintenance.
    All parts should be removed from their packaging and inspected for completeness any transport damage prior to installation.
    Shut off your water heating system and ensure that your mains stopcock is closed. Open the lowest hot and cold taps in the house and
    allow the water to run until the cold-water storage tank and pipes are fully empty. Please note, the hot water storage cylinder (if applicable)
    will always remain full.
    This mixertap requires a 35mm tap hole, if replacing an existing tap, remove the tap & clean the end of the feed pipes using wire wool the
    tap hole area should be free from dirt and sealant.
    This tap can be used in conjunction with a water softening system and will remove the need for a separate drinking water tap. In this
    instance the isolator valve (U) must cut into the unsoftened cold mains supply.
    Loosely position the tap and tail pipes to check if any alteration to the existing pipework is required, if this is the case do this now.

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om CDA TF10CH? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av CDA TF10CH att svara på din fråga.

Se manualen för CDA TF10CH helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 6.7. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om CDA TF10CH? Ställ din fråga här

CDA TF10CH – specifikationer

Varumärke CDA
Modell TF10CH
Produkt Kran
EAN 5060143313479
Språk Engelsk
Filtyp PDF
Vikt & dimension
Höjd (max.) 160
Produktens färg Krom

Letar du efter en manual? säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

© Copyright 2020 All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer