CDA TT40ANI

CDA TT40ANI bruksanvisning

(1)
  • For Service & Technical Support Call 01949 862012
    TT40 - quarter turn traditional lever monobloc
    Five Year warranty:
    In the unlikely event that you should experience any defect in the materials or workmanship of your new mixer within FIVE years of purchase,
    the purchaser’s sole remedy shall be the replacement (at the manufacturer’s discretion) of all or any part of the product that is defective. All
    working parts and valves are guaranteed for a period of FIVE years from purchase. Decorative surface finishes and O-rings are guaranteed
    for ONE year from the date of purchase provided that our advice concerning care has been observed. This guarantee is valid providing that
    the mixer tap has been used for normal domestic purposes in the UK and that the care, installation and maintenance instructions have been
    observed. The warranty extends to the original purchaser only. You should retain a copy of your dated invoice as proof of purchase to validate
    any claims under this guarantee.
    Care Instructions for your Kitchen Sink Mixer:
    To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean, soft damp cloth. A solution of warm water and
    a mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly and wiped dry. Any other cleaning action will
    invalidate your warranty. If the tap has a diffuser it should be cleaned periodically.
    Abrasive cleaners, scouring cleaners and acidic cleaners must not be used under any circumstances. Avoid contact with all solvents
    (including chlorinated solvents, ketones or acetones as these may result in surface deterioration or etching). Also avoid contact with any
    harsh household chemicals such as oven cleaners, drain cleaners, rust removers, paint strippers and toilet bowl cleaners, bar keepers friend
    or Brasso.
    Important Technical Data:
    Minimum operating pressure 0.3 bar Maximum hot water temperature 70°C*
    Maximum operating pressure 5.5 bar* Recommended hot water temperature 46°C
    *If these temperatures or pressures are exceeded, even for short periods, damage can result.
    CDA taps are either WRAS approved or manufactured in accordance with recognised European standards. Please ensure that your
    Kitchen mixer is fitted in accordance with Local Water Byelaws.
    These installation guidelines have been prepared for your direction and you must exercise due care at all times. We do not accept
    responsibility for problems that may occur through improper installation. Whilst assembling the tap take care not to accidentally loosen any
    screwed assemblies.
    Installation Preparation:
    Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any remaining solder,
    swarf or impurities from your system. Failure to carry out this simple procedure could cause problems or damage to the workings of the
    mixertap.
    We strongly recommend installing particle filter strainers and isolation valves to both the hot and cold feed pipes in an accessible position.
    This will help to prevent premature failure of the valves and ease any future maintenance.
    All parts should be removed from their packaging and inspected for any transport damage prior to installation.
    Shut off your water heating system and ensure that your mains stopcock is closed. Open the lowest hot and cold taps in the house and
    allow the water to run until the cold-water storage tank and pipes are fully empty. Please note, the hot water storage cylinder (if applicable)
    will always remain full.
    This mixertap requires a 35mm tap hole, if replacing an existing tap, remove the tap & clean the end of the feed pipes using wire wool the
    tap hole area should be free from dirt and sealant.
    Loosely position the tap and tail pipes to check if any alteration to the existing pipework is required, if this is the case do this now.
CDA TT40ANI

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om CDA TT40ANI? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av CDA TT40ANI att svara på din fråga.

Se manualen för CDA TT40ANI helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 6.8. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om CDA TT40ANI? Ställ din fråga här

CDA TT40ANI – specifikationer

Allmänt
Varumärke CDA
Modell TT40ANI
Produkt Kran
EAN 5060143313400
Språk Engelsk
Filtyp PDF
Vikt & dimension
Höjd (max.) 340
Egenskaper
Produktens färg Nickel

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer