Chamberlain KLIK1U

Chamberlain KLIK1U bruksanvisning

(1)
  • ON
    2 3
    1
    KG
    KG
    12 11 10 9 8 5 3 7 6 4 1 2
    CLICKER
    ®
    MODEL KLIK1U
    UNIVERSAL GARAGE DOOR OPENER REMOTE CONTROL
    Read instructions thoroughly BEFORE beginning.
    Start with garage door closed. Identify garage door opener type - Smart/Learn button
    or DIP Switch. Smart/Learn button or DIP Switches are located on motor unit or
    external receiver. Refer to owner’s manual if necessary.
    Clicker products are intended to be used only with garage door openers
    manufactured after 1993 that utilize photo-eyes safety sensors. These are always
    located on or near the bottom of the door track. If your garage door does not
    have the sensors attached and working, the opener is not compliant with current
    federal safety regulations and should be replaced.
    Proceed with instructions according to your type of garage door opener.
    To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
    ALWAYS keep remote controls out of reach of children. NEVER permit children to
    operate, or play with remote control transmitters.
    Activate gate or door ONLY when it can be seen clearly, is properly adjusted and
    there are no obstructions to door travel.
    ALWAYS keep gate or garage door in sight until completely closed. NEVER permit
    anyone to cross path of moving gate or door.
    © 2011, Clicker Corporation
    114A3485G All Rights Reserved
    OR
    DIP SWITCH SMART/LEARN BUTTON
    REMOTE CONTROL BATTERY
    NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver
    and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE
    NO OTHER USER SERVICEABLE PARTS.
    Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two
    conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
    interference received, including interference that may cause undesired operation.
    Dispose of batteries properly. Replace ONLY with 3V2032 coin batteries.
    To prevent possible SERIOUS INJURY or DEATH:
    NEVER allow small children near batteries.
    If battery is swallowed, immediately notify doctor.
    To reduce risk of fire, explosion or chemical burn:
    Replace ONLY with 3V2032 coin batteries.
    DO NOT recharge, disassemble, heat above 100° C (212° F) or
    incinerate.
    Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group.
    Genie and Intellicode are trademarks of GMI Holdings, Inc. Overhead Door is a
    Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation.
    Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears &
    Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark
    of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.
    DIP SWITCH SMART/LEARN BUTTON
    3
    Press program button until
    LED lights.
    1
    See Chart A to determine
    # of times to press
    button and write in blank
    on Step 5.
    1
    See Chart B to determine
    # of times to press
    button and write in blank
    on Step 5.
    * NOTE: LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible with
    Chamberlain technology.
    **NOTE: Visit www.clickerproducts.com for Genie Intellicode II instructions.
    Product Registration and Troubleshooting
    www.clickerproducts.com • 1-800-442-1255
    LED Indicator
    Button 1
    Button 2
    Program Button
    Battery
    DIP Switches
    Battery Cover
    NOTE:
    2 Position DIP Switch:
    If programming fails reverse
    DIP switches (OFF to ON and
    ON to OFF).
    ** 3 Position DIP Switch:
    For Chamberlain remotes DO NOT
    use the “0” position, use “+” or “-”. If you already have
    a 3-button remote, DIP switch #1 must be set to “-” if
    the large button is to open the door. It may be
    necessary to reprogram original remote controls.
    ON
    STOP
    CHART B
    # of times to
    press button Brand Description Year
    11 Chamberlain
    ®
    * 9 Position '90-'92
    12 Chamberlain
    ®
    *
    9 Position
    Canada
    '83-'89
    13 Genie
    ®
    12 Position '85
    14 Linear Multicode
    ®
    10 Position '76
    15 Chamberlain
    ®
    8 Position '83-'89
    16
    Stanley/
    Multicode
    ®
    10 Position '76
    17 Genie
    ®
    9 Position '85
    18
    Linear
    ®
    Moore-O-Matic
    ®
    8 Position '76
    19 Chamberlain
    ®
    7 Position '83-'89
    CHART A
    # of times to
    press button Brand
    Type/Color of
    Smart/Learn Year
    1 Linear
    ®
    Mega-Code '97-Current
    2 Chamberlain
    ®
    * Orange/Red '97-'03
    3 Chamberlain
    ®
    * Purple '05-Current
    4 Chamberlain
    ®
    * Green '93-'96
    5
    Genie
    ®
    Overhead Door
    ®
    Intellicode '95-Current
    6
    Genie
    ®
    **
    Overhead Door
    ®
    Intellicode '93-Current
    7 Stanley
    ®
    Secure Code '98
    8 Chamberlain
    ®
    * Yellow '11-Current
    9 Wayne Dalton
    ®
    Rolling Code '99
    11 Chamberlain
    ®
    9 Position '90-'92
    2
    2
    Programming complete. Press
    selected button to test. If unit
    does not work, return to Step 3.
    7
    Programming complete. Press
    selected button to test. If unit
    does not work, return to Step 3.
    7
    Press program button.
    6
    Press program button.
    6
    5
    OR
    OR
    Click
    NOTE: If there are problems
    programming to button 1,
    program to button 2.
    Select a button to program.
    Press button times ensuring
    LED stops flashing after each
    press. Code is accepted when
    one of the following occurs:
    2 3
    1
    KG
    KG
    Press and release the Smart/
    Learn button.
    Motor Unit
    4
    12 11 10 9 8 5 3 7 6 4 1 2
    3
    Match DIP switches. Turn
    extra switches OFF.**
    Motor
    Unit
    Existing
    Remote
    Clicker
    Remote
    4
    Press program button
    until LED lights.
    5
    Select a button to program.
    Press button times
    ensuring LED stops flashing
    after each press. Code is
    accepted when door
    activates.
    NOTE: Your opener may
    appear different and you may
    have to remove the light lens
    to access the learn button.
    2
Chamberlain KLIK1U

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Chamberlain KLIK1U? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Chamberlain KLIK1U att svara på din fråga.

Se manualen för Chamberlain KLIK1U helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 7.5. Den här manualen är tillgänglig på följande språk: Engels, Spaans. Behöver du hjälp eller har du en fråga om Chamberlain KLIK1U? Ställ din fråga här

Chamberlain KLIK1U – specifikationer

Allmänt
Varumärke Chamberlain
Modell KLIK1U
Produkt Fjärrkontroll
EAN 787083554513, 88021215344, 999993034621
Språk Engels, Spaans
Filtyp PDF
Prestanda
Antal stödda enheter 2
Maximal räckvidd - m
Lysdioder för överföring 1
Design
Gränssnitt -
Produktens färg Black,Grey
Kompatibilitet Genie\r\nLinear/Moore-o-Matic\r\nStanley\r\nOverhead Door\r\nWayne-Dalton\r\nCraftsman\r\nChamberlain\r\nLiftMaster\r\n300/310/315/372/390 MHz
Ingångssignal Tryckknappar
Display
Inbyggd display Nej
Vikt & dimension
Vikt - g
Batteri
Inbyggt batteri Nej
Uppladdningsbara Nej
Batteriteknik Litium
Batterityp CR2032
Antal batterier 1
Indikation
Indikator för låg batterinivå Nej

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Chamberlain KLIK1U .

Är din fråga inte listad? Ställ din fråga här

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2021 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer