CyberPower CP1500AVRLCD

CyberPower CP1500AVRLCD bruksanvisning

(1)
  • 1
    2
    3
    4
    5 6
    7
    8
    9
    10
    11
    12
    Automatic Voltage Regulators
    increase low or decrease high voltage to a computer
    safe 110/120 volts. The AVR automatically provides
    battery back-up power if line voltage drops below 90
    volts or exceeds 140 volts.
    AVR
    INCONSISTENT
    UTILITY POWER
    CONSISTENT
    SAFE POWER
    Min
    V
    ESTIMATE RUN_TIMEINPUT
    LOAD CAPACITY
    BATT. CAPACITY
    OUTPUT
    BATTERY
    A.V.R
    FAULT
    NORMALNORMAL
    SILENT
    OVER
    LOAD
    100
    IN OUT
    CP900AVRLCD / CP1100AVRLCD/
    CP1350AVRLCD / CP1500AVRLCD
    User’s Manual
    K01-0000002-01
    In purchasing a CP900AVRLCD / CP1100AVRLCD / CP1350AVRLCD / CP1500AVRLCD in the United States or Canada, the original end
    user receives a Limited Warranty and Connected Equipment Guarantee from Cyber Power Systems (USA), Inc. (for ease of reading,
    referred to as "CyberPower"). The Limited Warranty and the Connected Equipment Guarantee are intended to be the original end-user's
    exclusive rights and remedies. The Limited Warranty and the Connected Equipment are separate, all though they are related.
    Limited Warranty. The original end user (referred to as the "Initial Customer") receives an express limited warranty (referred to as the
    "Limited Warranty") for the CP900AVRLCD / CP1100AVRLCD / CP1350AVRLCD / CP1500AVRLCD purchased from CyberPower (referred
    to as the "Product"). The Limited Warranty is for the Product itself. The terms of the Limited Warranty are explained below.
    Connected Equipment Guarantee. CyberPower also provides the Initial Customer with protection in the event that the Product is not free
    from defects in materials and workmanship, and certain equipment connected to the Product is damaged (the "Connected Equipment
    Guarantee"). The Connected Equipment Guarantee protects the Initial Customer for damage to equipment plugged into the Product. The
    terms of the Connected Equipment Guarantee are explained below.
    The Limited Warranty and the Connected Equipment Guarantee are subject to the terms set forth below. Additionally, State or local law may
    adjust the terms of the Limited Warranty or the Connected Equipment Guarantee or may impose additional obligations, or additional "implied
    warranties." To the extent necessary to comply with those laws, the terms of the Limited Warranty and the Connected Equipment Guarantee
    should be read to adjust to those requirements only to the extent necessary to comply with such local law.
    If you are an Initial Customer, you are asked to read the following terms and conditions carefully before using the Product. By using the
    Product you consent to be bound by and become a party to the Limited Warranty and Connected Equipment Guarantee. If you do not agree
    to the terms and conditions of the Limited Warranty and Connected Equipment Guarantee, you should return the Product for a full refund
    prior to using it.
    REGISTRATION
    CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its
    website (www.cyberpowersystems.com) to establish that you are the Initial Customer of the Product, and therefore entitled coverage under
    the Limited Warranty and the Connected Equipment Guarantee. (Registration is not required for Limited Warranty coverage, but note if you
    do not complete a registration card you will be required to provide proof of purchase, as described below, to have the benefits of this Limited
    Warranty.)
    LIMITED WARRANTY
    CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years
    from the date of original purchase, subject to the terms of this Limited Warranty.
    Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to the
    period of ownership by the Initial Customer. This provision shall NOT create any Implied Warranty or Merchantability or of Fitness for a
    Particular Purpose that would not otherwise apply to the Product. NOTE: Some jurisdictions do not allow limitations on how long an
    implied warranty lasts, so the above limitation may not apply to you.
    To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty.
    Exclusive Remedies Under Limited Warranty.
    Your exclusive remedy and CyberPower's' sole obligations are as follows for the Product:
    If (a) the CyberPower Product you purchased and still own is defective in material or workmanship under this Limited Warranty or any
    applicable warranty imposed by law, and (b) all Limited Warranty requirements have been met, CyberPower will repair or replace the
    product if it proves to be defective in material or workmanship during the Warranty Period.
    Making a Limited Warranty Claim.
    To make a Limited Warranty claim on a Product, you must do the following:
    1. Complete and return the CyberPower Warranty Registration Card, or provide reasonable proof of purchase (for example, a sales receipt)
    that establishes you as the Initial Customer (the original end-user consumer purchaser) of the Product and prove that the Product was
    purchased within three (3) years of the event for which you want to make a claim for warranty service.
    2. Call CyberPower at (952) 403-9500 or (877) 297-6937 (toll free), write to CyberPower at 5555 12th Ave. East, Suite 110, Shakopee, MN
    55379, or e-mail CyberPower at claims@cyberpowersystems.com, within ten (10) days of the event for which you want to make a claim.
    3. When you contact CyberPower, identify the Product, the Purchase Date, and request Return Materials Authorization (RMA) information
    from CyberPower.
    4. Pack and ship the Product to CyberPower as instructed in your RMA. Show the RMA code on the shipping label or include it with the
    Product. You MUST prepay all shipping costs and you are responsible for packaging and shipment.
    CyberPower will inspect and examine the Product within ten (10) days of receipt. If the Product is not as warranted, CyberPower will repair
    (SAVE THESE INSTRUCTIONS)
    This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the
    unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.
    CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive
    contaminants. (Please see specifications for acceptable temperature and humidity range).
    CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. No user serviceable parts inside
    except for battery.
    CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.
    CAUTION! UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not
    grounded. If you need to de-energize this equipment, turn off and unplug the unit.
    CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a
    computer component.
    CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in
    accordance with the national Code, ANSI / NFPA 70.
    DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical
    applications. DO NOT use in any circumstance that would affect operation or safety of any life support equipment or with any medical
    applications or patient care.
    DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium.
    Condensation from the aquarium can cause the unit to short out.
    DO NOT USE WITH LASER PRINTERS! The power demands of these devices will overload and possibly damage the unit.
    UNPACKING
    Inspect the UPS upon receipt. The box should contain the following:
    (1) UPS unit; (1) User’s manual; (1) PowerPanel
    ®
    Personal Edition software CD; (1) USB device cable; (1) Telephone cable; (1) Warranty
    registration card; (1) Coaxial Cable
    OVERVIEW
    The CP900AVRLCD / CP1100AVRLCD / CP1350AVRLCD / CP1500AVRLCD provides automatic voltage
    regulation for inconsistent utility power. The CP900AVRLCD / CP1100AVRLCD / CP1350AVRLCD /
    CP1500AVRLCD features 890/1080/1500/1500 Joules of surge protection, and provides battery backup
    during power outages. The CP900AVRLCD / CP1100AVRLCD / CP1350AVRLCD / CP1500AVRLCD
    ensures consistent power to your computer system and its included software will automatically save your
    open files and shutdown your computer system during a utility power loss.
    AUTOMATIC VOLTAGE REGULATOR
    The CP900AVRLCD / CP1100AVRLCD / CP1350AVRLCD / CP1500AVRLCD stabilize inconsistent utility power. The incoming utility power
    may be damaging to important data files, but with Automatic Voltage Regulation, the computer will not experience damaging voltage levels.
    An Automatic Voltage Regulator automatically increases low or decreases high voltage to a consistent, computer safe 110v/120v. The unit’s
    powerful sealed lead-acid batteries will provide power only if the incoming voltage drops below 90v or increases above 140v.
    HARDWARE INSTALLATION GUIDE
    1.Your new UPS may be used immediately upon receipt. However, recharging the batteries for at least 16 hours is recommended to ensure
    that the battery’s maximum charge capacity is achieved. A loss of charge may occur during shipping and storage. To recharge the
    batteries, simply leave the unit plugged into an AC outlet. The unit will charge in both the ON as well as the OFF position.
    2.With the UPS unit off and unplugged, connect your computer, monitor, and any externally powered data storage device (Zip drive, Jazz
    drive, Tape drive, etc…) into the battery power supplied outlets. Plug your peripheral equipment (printer, scanner, speakers) into the full-
    time surge protection outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum or other large electrical
    device into the UPS. The power demands of these devices will overload and possibly damage the unit.
    3.To surge protect a network connection, connect a network cable from the wall jack outlet to the IN jack of the UPS.
    Then connect a network cable from the OUT jack on the UPS to the network device.
    4.Plug the UPS into a 2 pole, 3 wire grounding receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or circuit
    breaker and does not service equipment with large electrical demands (e.g. refrigerator, copier, etc…). The warranty prohibits the use of
    extension cords, outlet strips, and surge strips.
    5.Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will “beep” once.
    6.If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at
    least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker is depressed and
    then turn the UPS on.
    7.To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
    8.To store your UPS for an extended period, cover it and store with the battery fully
    charged. While in storage recharge the battery every three months to ensure battery
    life.
    HOW TO CONFIGURE THE OSX UPS
    FUNCTION IN ENERGY SAVER
    1. With the computer and the UPS off, connect the USB cable that was included with the
    unit to an available USB port on the computer.
    2. Turn the UPS on and start the computer.
    3. Once the computer has started open system preferences.
    4. In system preferences click on Energy Saver.
    5. Choose Settings for UPS and adjust your runtimes.
    DESCRIPTION
    1 Power Switch
    Used as the master on/off switch for equipment connected to the battery power supplied outlets.
    2 Power On Indicator
    This LED is under the power switch. It illuminates when the utility condition is normal and the UPS outlets are
    providing power, free of surges and spikes.
    3 LCD Module Display.
    High resolution and intelligent LCD display shows all the UPS information with icons and messages. For more information please check the
    “Definitions for Illuminated LCD Indicators” section.
    4 LCD Display Toggle/Selected Switch
    The switch can be used to select the LCD display contents including Input Voltage, Output Voltage and Estimated Run
    Time. The toggle frequency is set to one time per second. Holding the switch for more than two seconds while running
    on battery will silence the buzzer.
    5 Battery and Surge Protected Outlets
    The unit has four battery powered/surge protected outlets for connected equipment and ensures temporary
    uninterrupted operation of your equipment during a power failure.
    6 Full-Time Surge Protection Outlets
    The unit has four always on surge suppression outlets.
    7 Electrical Wiring Fault Indicator
    This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring. If
    this is illuminated, user is advised to disconnect all electrical equipment from the outlet and have an electrician check to ensure the outlet is
    properly wired. The unit will not provide surge protection without being plugged into a grounded and properly wired wall outlet.
    8 Communication Protection Ports
    Communication protection ports will protect any standard modem, fax , telephone line, broadband network or Ethernet connection.
    9 Circuit Breaker
    Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.
    10 Serial/USB Ports to PC
    The ports allow connection and communication from the USB or DB-9 serial port on the computer to the UPS unit. The USB port will
    communicate with PowerPanel
    ®
    Personal Edition and the DB-9 port is for use with a serial cable and the Microsoft
    ®
    UPS Service.
    Note: Only one of these two ports can be used to communicate with your computer at one time.
    Note: To install PowerPanel
    ®
    Personal Edition Software the computer will need Microsoft
    ®
    Internet Explorer 5.0 or higher installed.
    Note: If using the Serial Port please read the directions to configure the Microsoft UPS service on our website
    http://www.cyberpowersystems.com/ups_service.asp . If you need a serial cable please contact CyberPower technical support at
    tech@cyberpowersystems.com
    11 Coax/Cable/DSS Surge Protection
    The Coax/Cable/DSS surge protection ports will protect any cable modem, CATV converter, or DSS receiver.
    12 Outlets Designed for AC Adapters
    The unit has four outlets spaced to allow AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets.
    CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the
    supervision of personnel knowledgeable of batteries and their precautions.
    CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.
    CAUTION! The battery may present a risk of electrical shock. Do not dispose of battery in a fire as it may explode. Follow all local
    ordinances regarding proper disposal of batteries. Almost any retailer that sells lead-acid batteries collects used batteries for recycling, as
    required by most state laws.
    CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to skin and eyes and may be toxic.
    CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following precautions before replacing the
    battery:
    1.Remove all watches, rings or other metal objects.
    2.Only use tools with insulated handles.
    3.Do not lay tools or metal parts on top of battery or any terminals.
    4.Wear rubber gloves and boots.
    5.Determine if the battery is inadvertently grounded. If grounded, remove the source of ground. CONTACT WITH GROUNDED BATTERY
    CAN RESULT IN ELECTRICAL SHOCK!
    Model CP900AVRLCD CP1100AVRLCD CP1350AVRLCD CP1500AVRLCD
    Capacity 900VA / 560W 1100VA / 640W 1350VA / 810W 1500VA / 900W
    Input Voltage on Utility 90V to 140V
    Input Frequency 60 Hz ± 3 Hz
    On-Battery Output Voltage 120Vac ± 5%
    Transfer Time 4ms Typical
    Max. Load for UPS Outlets 900VA / 560W 1000VA / 580W 1285VA / 750W 1500VA / 900W
    Max. Load for Full-Time
    Surge Protection outlets (8 Outlets)
    12 Amps
    On-Battery Output Wave Form Simulated Sine Wave Form
    Operating Temperature + 32°F to 95° F / 0° C to 35° C
    Operating Relative Humidity 0 to 95% NON-CONDENSING
    Size (L x W x H)
    13 5/16” x 4” x 9 7/8”
    33.8 x 10.0 x 24.9cm
    Net Weight 22.2 lbs 24.4 lbs 25.6 lbs
    Typical Battery Recharge Time 8 hours typical from total discharge
    Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles
    Battery Type Spill-proof, Maintenance-free, sealed lead-acid
    Safety Approvals UL1778(UPS), cUL107., FCC/DoC Class B
    Model iMac G4
    Desktop PC  Desktop PC Desktop PC  Desktop PC
    with 17”LCD Monitor with 19”LCD Monitor with 21”LCD Monitor with CRT Monitor
    CP900AVRLCD 105 minutes 79 minutes 51 minutes 47 minutes 40 minutes
    CP1100AVRLCD 145 minutes 79 minutes 51 minutes 47 minutes 40 minutes
    CP1350AVRLCD 148 minutes 89 minutes 57 minutes 52 minutes 47 minutes
    CP1500AVRLCD 170 minutes 90 minutes 57 minutes 55 minutes 49 minutes
    IMPORTANT SAFETY WARNINGS
    INSTALLING YOUR UPS SYSTEM
    BASIC OPERATION
    TROUBLE SHOOTING
    DEFINITIONS FOR ILLUMINATED LED INDICATORS
    Limited Warranty and Connected Equipment Guarantee
    TECHNICAL SPECIFICATIONS
    1. Turn off and unplug all connected equipment.
    2. Turn the UPS off and unplug it from the AC power source.
    3. Turn the UPS upside down.
    4. Remove the retaining screw.
    5. Slide the battery compartment cover (front panel) completely off of the unit.
    6. Remove the batteries from the compartment.
    7. Disconnect the battery wires from the batteries.
    8. Install the replacement batteries by connecting the red wire and black wire to the same color
    wires from the battery pack.
    9. Put the batteries back into the compartment.
    10. Slide back the battery compartment cover and tighten the retaining screw.
    11. Recharge the UPS for 8-16 hours to fully charge the battery.
    The LCD display indicates a variety of UPS
    operational conditions. All descriptions apply
    when the UPS is plugged into an AC outlet
    and turned on or when the UPS is on battery.
    INPUT voltage meter: This meter measures the AC voltage that the UPS system is
    receiving from the utility wall outlet. The UPS is designed, through the use of automatic
    voltage regulation, to continuously supply connected equipment with stable, 110/120
    output voltage. In the event of a complete power loss, severe brownout, or over-voltage,
    the UPS relies on its internal battery to supply consistent 110/120 output voltage. The
    INPUT voltage meter can be used as a diagnostic tool to identify poor-quality input power.
    OUTPUT voltage meter: This meter measures, in real time, the AC voltage that the UPS
    system is providing to the computer, such as normal line mode, AVR mode, and battery
    back up mode.
    Note: The OUTPUT voltage meter shows the status of the battery back up outlets.
    ESTIMATE RUN TIME: This displays the run time estimate of the UPS with the current
    battery capacity and load.
    NORMAL icon: This icon appears when the UPS is working under normal conditions.
    BATTERY icon: During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps followed by a pause) to
    indicate the UPS is operating from its internal batteries. During a prolonged brownout or blackout, the alarm will sound continuously (and the
    BATT.CAPACITY meter shows one 20% capacity segment shaded) to indicate the UPS’s batteries are nearly out of power. You should save
    files and turm off your equipment immediately.
    AVR (Automatic Voltage Regulator) icon: This icon appears whenever your UPS is automatically correcting low AC line voltage without
    using battery power. This is a normal, automatic operation of your UPS, and no action is required on your part.
    SILENT MODE icon:This icon appears whenever the UPS is in silent mode. The buzzer does not beep during silent mode until the battery
    reaches low capacity.
    OVER LOAD icon: This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To clear the overload,
    unplug some of your equipment from the battery-supplied outlets until the icon turns off and the alarm stops.
    FAULT icon: This icon appears if there is a problem with the UPS. Contact CyberPower Systems at tech@cyberpowersystems.com for
    further help and support.
    BATT. CAPACITY meter: This meter displays the approximate charge level (in 20% increments) of the UPS’s internal battery. During a
    blackout or severe brownout, the UPS switches to battery power, the BATTERY icon appears, and the charge level decreases.
    LOAD CAPACITY meter: This meter displays the approximate output load level (in 20% increments) of the UPS’s battery outlets.
    Alarm
    Condition
    On Off Off Normal
    On On/Off
    2 beeps
    per 30 seconds
    On On/Off Rapid beeps
    On On/Off Long beeps
    On On None
    POWER
    ON
    WIRING
    FAULT
    Utility failure—The UPS is providing battery power to the battery power-
    supplied outlets.
    Utility failure—The UPS is providing battery power.The rapid beeps mean
    that the battery will run out of charge within a few minutes.
    Battery overload—Occurs in the battery power-supplied outlets. Turn off
    the UPS and unplug at least one piece of equipment from the UPS. Wait
    10 seconds, press the circuit breaker reset button, then turn the UPS on.
    Electrical wiring fault—This means there’s a wiring problem within the
    utility AC power outlet. A wiring problem could be a bad ground, missed
    ground, or reversed wiring. You should disconnect all equipment from
    the outlet and have it checked by an electrician.
    REPLACING THE BATTERY
    DEFINITIONS FOR ILLUMINATED LCD INDICATORS
    REMINDER: Batteries are consider HAZARDOUS WASTE and must be disposed of properly. Almost any retailer that sells lead-acid
    batteries collects used batteries for recycling, as required by most state laws.
    Additional troubleshooting information can be found at
    www.cyberpowersystems.com/support.htm
    Problem Possible Cause Solution
    Full-time surge protection outlets
    stop providing power to equipment.
    Circuit breaker button is projecting
    from the side of the unit.
    Circuit breaker has
    tripped due to an
    overload.
    Turn the UPS off and unplug at least one piece of equipment.
    Wait 10 seconds, reset the circuit breaker by depressing the
    button, and then turn the UPS on.
    The UPS does not perform
    expected runtime.
    Recharge the battery by leaving the UPS plugged in.
    Contact CyberPower Systems about replacement batteries at
    tech@cyberpowersystems.com
    Battery is slightly worn out.
    Battery not fully charged.
    The UPS will not turn on.
    The on/off switch is designed
    to prevent damage by rapidly
    turning it off and on.
    Turn the UPS off. Wait 10 seconds and then turn the UPS on.
    The unit is not connected to an
    AC outlet.
    The unit must be connected to a 110/120v 60Hz outlet.
    The battery is worn out.
    Contact CyberPower Systems about replacement batteries at
    tech@cyberpowersystems.com
    Mechanical problem.
    Contact CyberPower Systems at
    tech@cyberpowersystems.com
    PowerPanel
    ®
    Personal Edition is
    inactive (all icons are gray).
    The USB cable is not
    connected.
    Connect the USB cable to the UPS unit and an open USB port
    on the back of the computer. You must use the cable that
    came with the unit.
    The USB cable is connected
    to the wrong port.
    Check the back of the computer for an additional USB port.
    Move the cable to this port.
    The unit is not providing
    battery power.
    Shutdown your computer and turn the UPS off. Wait 10
    seconds and turn the UPS back on. This should reset the unit.
    EXPECTED RUNTIME IN MINUTES
    (Due to the differences in computer components, the runtime will vary.)
    or replace the Product and return it to you at CyberPower's expense, or, if CyberPower is unable to or decides not to repair or replace the
    Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product (purchase
    receipt showing price paid is required).
    CONNECTED EQUIPMENT GUARANTEE
    If you are the Initial Purchaser and the Product is still covered by the Limited Warranty, the Connected Equipment Guarantee provides
    protection for damage to equipment connected to the Product ("Connected Equipment"), subject to certain terms and limitations.
    The Connected Equipment Guarantee is not "first dollar" coverage. It is secondary. If you have any other source of payment for your loss,
    such as insurance, another warranty, or an extended warranty or purchase protection plan (“Primary Coverage”), CyberPower’ will pay only
    to the extent that that the Primary Coverage does not cover the loss. CyberPower's obligation is reduced by any amounts that you are
    entitled to recover from the Primary Coverage, whether or not you make a claim for recovery under any applicable Primary Coverage.
    The Limited Warranty does not cover Connected Equipment, but as is explained below, to be covered under the Connected Equipment
    Guarantee, the Connected Equipment must have been damaged due to a failure of the Product. The Connected Equipment must have been
    damaged due to a defect in materials or workmanship of the Product
    In the event of damage to the Connected Equipment, your exclusive remedies, and CyberPower’s sole obligations, are as follows for
    Connected Equipment. If (a) the Product purchased and owned by you is defective in material or workmanship; (b) the Limited Warranty
    requirements have been met (except that the three year limitation of the Limited Warranty does not limit the Connected Equipment
    Guarantee, which is for the lifetime of the Product), and; (c) none of the limitations or exclusions on warranty coverage apply (or than the
    three year limit), CyberPower will (as CyberPower elects, as permitted by law), repair, replace, or pay the Agreed Damage Amount (defined
    below) for, the item(s) of your electronic equipment directly and properly connected to the product (the "Connected Equipment") if that
    Connected Equipment is (x) damaged by AC power line transients, spikes, or surges on properly installed, grounded, and code-compliant
    120 volt power lines in the United States and Canada, or by transients, surges or spikes on standard telephone equipment lines, or Base
    10/100T Ethernet lines that are properly installed and connected (a "Power Disturbance") and (y) is directly plugged into and properly
    connected to a CyberPower Product in its original condition which is properly operated when a Power Disturbance passes through the
    CyberPower Product and (y.1) exhausts the protection capacity of the CyberPower Product or (y.2) damages the CyberPower Product. This
    provision sets out the only liability of any character of CyberPower for direct, indirect, special, consequential, and/or incidental damages
    under our Limited Warranty, applies only to Connected Equipment, and all such Liability is limited to the Agreed Damage Amount.
    Making a Connected Equipment Guarantee Claim.
    To make a Warranty claim for damage to Connected Equipment under the Connected Equipment Guarantee, you must do the following:
    1. Complete and return the CyberPower Warranty card or provide reasonable proof of purchase, for example, a sales receipt that
    establishes you as the original end-user consumer purchaser of the Product.
    2. Call CyberPower at (952) 403-9500 or (877) 297-6937 (toll free), write to CyberPower at 5555 12th Ave East, Suite 110, Shakopee, MN
    55379, or e-mail CyberPower at claims@cyberpowersystems.com within ten (10) days of the date of the event for which you wish to make a
    claim for warranty service.
    3. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on
    all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and the name of the power utility
    supplier for the location of the Connected Equipment and Request a Claim Number.
    4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage
    to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include
    it with the product. Initial Customer shall prepay all shipping costs, must pay the cost of the repair estimate, and is responsible for
    packaging and shipment.
    CyberPower’s Duties.
    CyberPower will inspect and examine the Product and the item(s) of Connected Equipment (or at CyberPower's election, your written
    statement and repair cost estimate for those item(s)). You must return the product for inspection.
    If the damage to Connected Equipment is covered by the Connected Equipment Guarantee, CyberPower will (in addition to Limited
    Warranty remedies for the CyberPower Product itself) repair (or pay the costs of repair) or replace the Connected Equipment or, at the
    option of CyberPower, as permitted by law, pay to the Initial Customer the "Agreed Damage Amount" (up to the aggregate limits stated
    below) for all item(s) of Initial Customer's Connected Equipment. The "Agreed Damage Amount" for all items of Initial Customer's Connected
    Equipment shall be the lesser of the amount determined under Clause (1) or (2) below, reduced by any amounts described in Clause (3)
    below:
    1. The fair market value of the Connected Equipment as established by the lower of (a) the price list of Orion Blue Book on the date of
    occurrence (or if such price list is no longer published, a published or announced price list reasonably selected by CyberPower), or (b) the
    average price the same or similar items are being sold for on
    E-bay, or (c) the lowest price the same or similar items can be purchased for in the United States; or
    2. The aggregate ceiling amount for all Connected Equipment: CyberPower CP900AVRLCD - $300,000.00. CP1100AVRLCD - $375,000.00.
    CP1350AVRLCD - $425,000.00. CP1500AVRLCD - $500,000.00.
    3. The amount(s) of all payment you have or are entitled to receive from insurance, other warranties, extended warranties, or from other
    sources or persons for the Connected Equipment or damage to such equipment so that CyberPower’s maximum liability shall be reduced to
    reflect all such other payments or sources of recovery
    If CyberPower replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount, the Initial Customer shall
    transfer ownership of all item(s) to CyberPower without warranty by the Initial Customer, but free of lien or other interest.
    CONDITIONS COMMON TO THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE
    The Limited Warranty and the Connected Equipment Guarantee are the only and the exclusive express warranty of CyberPower with
    respect to the Product. This exclusion of other express warranties applies to written and oral express warranties.
    LIMITATION: THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE DOES NOT COVER
    The Limited Warranty and the Connected Equipment Guarantee are intended to exclusive rights and remedies and replace any other rights,
    to the extent allowed by law.
    1. As to the CyberPower Product, the limited warranty does not cover or apply to: misuse, modification, operation or storage outside
    environmental limits for the Products, in transit, in shipment, or in storage, damage or deterioration, improper operation or maintenance, or
    use with items or equipment not designed or intended for use with the product.
    2. As to Connected Equipment, the Connected Equipment Guarantee covers only damage within the specific terms of the Connected
    Equipment Guarantee to Connected Equipment (and only up to the applicable aggregate ceiling amount).
    3. The Connected Equipment Guarantee does not cover damage to Connected Equipment or apply if the Product has been operated in a
    failure mode or not in compliance with CyberPower operating instructions and manuals, or if the Connected Equipment has been operated
    in a failure mode or not in compliance with the instructions and manuals of its manufacturer/vendor.
    The Limited Warranty and the Connected Equipment Guarantee Do Not Apply Unless The Initial Customer:
    1. Has properly connected the Product and the Connected Equipment to properly wired and grounded outlets (including compliance with
    electrical and safety codes of the most current electrical code (ANS/NFPA 70), without the use of any adapters, extension cords or other
    connectors.
    2. Has provided a suitable and proper environment for use and installation of the Product and Connected Equipment.
    3. Has properly installed and operated the CyberPower Product and Connected equipment.
    4. Has operated the Product at all times within the limitations on the Product’s VA capacity as stated in this User Manual.
    CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following:
    1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.
    2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120
    volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment
    lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion applies, for example, to fluctuations in data
    transmission or reception, by CATV or RF transmission or fluctuations, or by transients in such transmission.
    3. Damage from any circumstance described as excluded above with respect to the product.
    4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or
    the Connected Equipment.
    Exclusion of Consequential and Other Damages.
    The sole and exclusive remedies of the Initial Customer are those provided by the Limited Warranty and Connected Equipment Guarantee.
    CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower
    excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT
    FOR (AND ONLY FOR) the specific limited agreement of CYBERPOWER to provide certain warranty benefits regarding "Connected
    Equipment" under the "CYBERPOWER Connected Equipment Guarantee"], loss of profits, business interruption, or loss of information or
    data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above
    limitation may not apply to you.
    DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.
    CyberPower does not sell the Products for use in high-risk activities. The Product is not designed or intended for use in hazardous
    environments requiring fail-safe performance, including the operation of nuclear facilities, aircraft navigation or communication systems, air
    traffic control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the Product could
    lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life
    support device (collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of fitness for High Risk
    Activities. CyberPower does not authorize use of any of its products use in any High Risk Activities.
    ANY SUCH USE IS IMPROPER AND IS A MISUSE OF CYBERPOWER PRODUCTS.
    The Limited Warranty and the Connected Equipment Guarantee are governed by the laws of the United States and the State of Minnesota,
    without reference to conflict of law principles. The application of the United Nations Convention of Contracts for the International Sale of
    Goods is expressly excluded.
    Contact Information: CyberPower's address is 5555 12th Ave East, Suite 110, Shakopee, MN 55379 and its phone number is (952) 403-
    9500 or Toll-free: (877) 297-6937. CyberPower is the warrantor under this Limited Warranty. You may also contact CyberPower on the
    Internet at www.cyberpowersystems.com.
    FCC Notice
    This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.
    These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment
    generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
    harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
    this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
    on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving
    antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different
    from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. Any special
    accessories needed for compliance must be specified in the instruction.
    CAUTION: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio
    and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this
    equipment.
    CAUTION: Any changes or modifications not expressly approved by the guarantee of this device could void the user’s authority to operate
    the equipment.
    TO REPLACE THE BATTERY
CyberPower CP1500AVRLCD

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om CyberPower CP1500AVRLCD? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av CyberPower CP1500AVRLCD att svara på din fråga.

Se manualen för CyberPower CP1500AVRLCD helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 8.6. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om CyberPower CP1500AVRLCD? Ställ din fråga här

CyberPower CP1500AVRLCD – specifikationer

Allmänt
Varumärke CyberPower
Modell CP1500AVRLCD
Produkt Avbrottsfri strömförsörjning (UPS)
EAN 649532015269, 6495320152692, 761878233470
Språk Engelsk
Filtyp PDF
Egenskaper
Uteffekt kapacitet (VA) 1500
Uteffekt 900
Energivärdering 1500
Ingångsfrekvens 60
Svarstid (medel) 4
Hörbart larm
UPS-topologi Line-interactive
Övrigt
Anslutningsdetaljer utgång NEMA 5-15R
Anslutningsdetaljer ingång NEMA 5-15P
Produktstorlek (BxDxH) 101.6 x 336.55 x 247.65
Vikt (imperial) 25
Omgivningstemperatur vid drift 32 - 95
Dimension (B x D x H) (imperial) 4 x 13.25 x 9.75
Batteri
Batteriteknik Slutna blybatterier (VRLA)
Normal drifttid vid halv belastning 11
Normal drifttid vid full belastning 3
Laddningstid 16
Utbytbara batteripatroner BB - HR1234W
Design
Formfaktor Tower
Certifiering UL1778, cUL, FCC DOC Class B
Anslutningar
Seriella portar 1
Modem (RJ-11) portar 1
Antal LAN (RJ-45) anslutningar 1
Antal USB 2.0 anslutningar 1
Vikt & dimension
Vikt 11339
Miljökrav
Temperatur vid drift 0 - 40
Intervall för relativ operativ luftfuktighet 0 - 95

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer