CyberPower UR700RM1U

CyberPower UR700RM1U bruksanvisning

(1)
  • UR500/ UR700
    Guaranteed Uninterruptible Power System
    3
    INSPECTION
    The box should contain the following:
    (1) PowerPanel™ software (floppy disk); (1) serial interface cable (DB-9);
    (1) Telephone communication cable; (1) user manual; (1) warranty registration card;
    (1) UPS unit.
    HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
    1. Make sure that the total Volt-Amp (VA) requirements of your computer, monitor and peripheral
    equipment does not exceed 1440 VA.
    2. Insure that the equipment plugged into the three battery power-supplied outlets does not exceed
    the UPS unit’s rated capacity (500VA/275W for UR500, 700VA/360W for UR700). If rated unit
    capacities are exceeded, an overload condition may occur and cause the UPS unit to shut down
    and the circuit breaker to trip.
    3. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert
    Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only
    calculates the maximum amount of VA that the equipment can use, not what is typically used by
    the equipment at any one time. Users should expect usage requirements to be approximately
    60% of below value to estimate power requirements:
    Watts (W) x 1.82 = VA or Amps (A) x 120 = VA
    Add the totals up for all pieces of equipment and multiply this total by .6 to calculate actual re-
    quirements.
    There are many factors that can effect the amount of power that your computer system will re-
    quire. The total load that you will be placing on the battery-powered outlets should not exceed
    80% of the unit’s capacity.
    4
    Hardware Installation Guide
    1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at
    least four hours is recommended to insure that the battery’s maximum charge capacity is
    achieved. Charge loss may occur during shipping and storage. To recharge the battery, simply
    leave the unit plugged into an AC outlet. The unit will charge in both the on as well as the off po-
    sition.
    2. If you wish to use the software, connect the enclosed serial interface cable to the serial port on
    the UPS and an open serial port on the computer. If you are not going to use the software, you
    do not need to connect the cable.
    3. With the UPS unit off and unplugged, connect
    your computer, monitor, and any externally
    powered data storage device (Zip drive, Jazz
    drive, Tape drive, etc…) into the battery power
    supplied outlets. Plug your peripheral equipment
    (printer, scanner, speakers) into the full-time surge protection outlets. DO NOT plug a laser
    printer, copier, space heater, vacuum, paper shredder or other large electrical device into
    the UPS. The power demands of these devices will overload and possibly damage the
    unit.
    4. To protect a fax, telephone, modem line or network cable, connect a
    telephone cable or network cable from the wall jack outlet to the IN jack of
    the UPS. Then connect a telephone cable or network cable from the OUT
    jack on the UPS to the modem, computer, telephone, fax machine, or
    network device.
    5. Plug the UPS into a 2 pole, 3 wire grounding receptacle (wall outlet). Make sure the wall branch
    outlet is protected by a fuse or circuit breaker and does not service equipment with large electrical
    demands (e.g. refrigerator, copier, etc…). Avoid using extension cords. If used, the extension
    cord must be rated for 15 amps.
    6. Depress the power switch to turn the unit on. The power on indicator light will illuminate and the
    unit will “beep” once.
    7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To
    correct this, turn the UPS off and unplug at least one piece of equipment from the battery power
    supplied outlets. Wait 10 seconds. Make sure the circuit breaker is depressed and then turn the
    UPS on.
    8. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet,
    the battery will automatically recharge.
    9. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
    10. To store your UPS for an extended period, cover it and store with the battery fully charged. Re-
    charge the battery every three months to insure battery life.
CyberPower UR700RM1U

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om CyberPower UR700RM1U? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av CyberPower UR700RM1U att svara på din fråga.

Se manualen för CyberPower UR700RM1U helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 6.5. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om CyberPower UR700RM1U? Ställ din fråga här

CyberPower UR700RM1U – specifikationer

Allmänt
Varumärke CyberPower
Modell UR700RM1U
Produkt Avbrottsfri strömförsörjning (UPS)
EAN 649532607006
Språk Engelsk
Filtyp PDF
Egenskaper
Uteffekt kapacitet (VA) 700
Energivärdering 1736
Uteffekt 360
Överspänningsskydd
Hörbart larm
EMI / RFI-brusfiltrering
Övrigt
Batterityp BB 6V/7AH
Anslutningsdetaljer utgång 4 x NEMA 5-15R
Anslutningsdetaljer ingång NEMA 5-15P
Kompatibla operativsystem Windows 2000, 2003, XP 32/64, Vista 32/64, 7, Server 2008
Batteri
Batteriteknik Slutna blybatterier (VRLA)
Laddningstid 8
Normal drifttid vid halv belastning 9
Normal drifttid vid full belastning 2
Design
Formfaktor -
Kabellängd 3
Produktens färg Svart
LED-indikatorer
Certifiering UL1778, cUL, FCC DOC Class B
ROHS
Rackkapacitet 1U
Anslutningar
Seriella portar 1
Modem (RJ-11) portar 1
Antal LAN (RJ-45) anslutningar 1
Antal USB 2.0 anslutningar 0
Vikt & dimension
Vikt 5443.1
Bredd 438.15
Djup 234.95
Höjd 44.45
Förpackning
Medföljande programvara PowerPanel

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer