Draper Cineperm

Draper Cineperm bruksanvisning

(1)
  • Installation Instructions
    Cineperm Permanently Tensioned Projection Screen by Draper
    Copyright © 2011 Draper Inc. Form Cineperm_Inst11 Printed in U.S.A.
    Frame Assembly
    Standard Frame—
    Lay out frame pieces on fl oor, by matching up color-coded tape near
    corners. Snaps should be facing up.
    Assemble frame (see Fig. 1). If nec es sary gently tap frame ends with a
    rubber mallet to make sure castings are fully seated.
    Surface Installation
    Carefully remove surface from cardboard tube and unroll onto a clean
    cloth or paper.
    Engage snaps in each corner, then secure rest of screen snaps.
    Stretch fabric across frame. Use extreme caution when attaching fabric.
    Overstretching or rough handling could cause the viewing surface to tear.
    Frame Installation (Standard Frame)
    Outside (Face) Mount—
    Drill mounting holes in frame (see Fig. 2).
    Mark wall and drill holes to correspond with those in the frame.
    Enlarge holes in frame side furthest from wall to allow screw heads to pass
    through (see Fig. 2). Do not allow screw heads to remain outside the
    frame: overtightening could bend frame and affect screen fl atness.
    Cineperm
    frame
    Mounting hardware
    by others
    Viewing surface snaps to
    frame, covering mounting holes
    Supporting structure
    Drill through frame for
    mounting hardware.
    Enlarge first hole for screw
    head to pass through.
    Figure 2
    Figure 3
    Inside (Jamb) Mount—
    Place frame assembly in opening to check for a snug fi t. If frame is too
    large, opening may have to be enlarged. If frame is too small or does not
    sit square in the opening, shims and caulking may be required.
    Drill mounting holes in frame, and enlarge the fi rst holes to allow screw
    heads to pass through (see Fig. 3). Do not allow screw heads to remain
    outside the frame: overtightening could bend frame and affect screen
    atness.
    Drill holes in jamb.
    Attach frame using appropriate fasteners for mounting surface (provided
    by others).
    Use caulk to ensure there is no light leakage around edges of frame.
    Truss Frame—
    Unfold and lay out pieces on fl oor, by matching up color coded marks.
    Lock all hinges (see Fig. 1). Stage Left and Stage Right sections should be
    placed with snaps up. Top and bottom sections should be placed with
    snaps down.
    To increase frame rigidity, hinges on top and bottom sections have rivnuts
    marked with red and green. Insert a Handy Crank through the threadless
    rivnut (red) and tighten into the threaded rivnut (green).
    Apply small sections marked “Stiffener Bars” to back of bottom frame
    section, using 8 Handy Cranks. These eliminate sag on large suspended
    frames. Failure to use all Handy Cranks may result in screen frame
    damage. Turn bottom frame section over so snaps face up.
    Repeat step 3 for top frame section.
    Join top and bottom sections to Stage Left and Stage Right, using 2
    Handy Cranks on each of the 4 corners. Match numbers on white labels.
    NOTE: No Handy Crank should protrude outside screen frame.
    Attach surface (see “Surface Installation”), and suspend using appropriate
    materials (provided by others to meet specifi c installation requirements).
    Opening
    Wall
    Anchor bolt by others.
    Clearance hole in outer
    wall by others.
    Snap-on viewing surface
    1" square
    alum. tube
    Wall
    Anchor bolt by others.
    Clearance wall in outer
    wall by others.
    Locate between snaps.
    1 square
    alum. tube
    Snap-on viewing surface
    Inside (Jamb) Mount
    Outside (Face) Mount
    Attach frame to wall using appropriate fasteners for mounting surface
    (provided by others).
    NOTE: Measure screen frame width at the top, bottom, and center; Make
    sure the frame is installed so the center width is same as the width at
    the top and bottom.
    Figure 1
    Standard Frame
    Truss Style Frame
    Caution
    Read instructions through completely before pro ceed ing.
    Follow instructions carefully. Installation con trary to instructions
    invalidates warranty.
    Bent or warped frames will affect surface fl atness and image quality.
    Screen should be square, and width should not vary from the center to
    the ends of the frame
    When lifting assembled screen, do not lift at only one corner; lift at both
    corners. Lifting by one corner could result in damage to the screen
    frame, especially on large screens.
    Screen should be installed level (using a carpenter’s level).
    Nothing should be fastened to screen frame or viewing surface.
    Be careful not to rip screen material when attaching surface to frame.
    The ideal temperature range for assembling this screen to prevent
    damaging the surface is 68°-78° F (20°-26° C). Assembling below
    recommended temperatures may damage surface and void warranty.
    NOTE: Screen has been inspected and tested at factory prior to shipment.
    Jamb of opening
    Viewing Surface snaps to
    frame, covering mounting holes
    Cineperm
    frame
    Drill through frame for
    mounting hardware. Enlarge
    first hole for screw head
    to pass through.
    Mounting hardware
    by others
    Color-coded
    tape
    ®
    Handy
    Cranks
    If you encounter any diffi culties installing or servicing your Cineperm, call your
    dealer or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.
    Always fold viewing surface with snaps face-to-face.
    Do not permit screen fabric to contact border material
    or snaps when folded. Store in pouch provided.
Draper Cineperm

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Draper Cineperm? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Draper Cineperm att svara på din fråga.

Se manualen för Draper Cineperm helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 9.5. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Draper Cineperm? Ställ din fråga här

Draper Cineperm – specifikationer

Allmänt
Varumärke Draper
Modell Cineperm
Produkt Projektions skärm
EAN 641092147220, 6410921472208
Språk Engelsk
Filtyp PDF
Prestanda
Native bildförhållande 4:3
Sammanlagd skärmstorlek (höjd x bredd) 137 x 183
Diagonal 90
Vikt & dimension
Vikt 9979

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer