Draper Luma 207101

Draper Luma 207101 bruksanvisning

(1)
  • Crimp
    Crimp
    Luma pictured
    Operating Instructions—Standard
    To lower picture surface, pull screen down. Hesitate—then allow screen to retract
    very slowly until it locks in place.
    To raise picture surface, pull screen down and, while holding, allow for slow
    retraction into the case to reduce risk of injury from falling screen.
    Operating Instructions—AutoReturn (Available with Luma)
    To lower picture surface, pull screen down. Hesitate—then allow screen to retract
    very slowly until it locks in place.
    To raise picture surface, pull screen down gently until it stops, then release.
    Wall Mounting
    (Hardware not Included)
    Ceiling Suspended
    (Hardware not Included)
    T–Bar Twist Clips
    (Optional Equipment)
    Extension Brackets
    (Optional Equipment)
    If you encounter any diffi culties installing or servicing your screen, call your dealer
    or Draper, Inc., Spiceland, Indiana, (765) 987-7999, or fax (765) 987-7142.
    Copyright © 2010 Draper Inc. Form Luma-Star_Inst10 Printed in U.S.A.
    Installation/Operating Instructions
    Luma and Star Spring Roller Operated Projection Screens by Draper
    Installation
    Your Draper screen can be mounted on a wall or suspended from the ceiling or
    extension brackets. It must be mounted level and with the fl at back parallel to the
    wall.
    The screen (or extension brackets) should be mounted into studs or blocking in the
    wall/ceiling, or in drywall (minimum thickness ½") with specifi ed anchors. For any
    other type of installation, follow all local build ing and safety codes.
    Steel studs, concrete or cinder block walls and all other types of non-wood frame
    construction require the use of special screws or anchors.
    The selection of ap pro pri ate mounting hardware should be made by a
    qualifi ed professional installer.
    Use the upper portion of the holes at the back of the endcap/mounting bracket
    for fl ush wall mount ing. Recommended hard ware (not included): For mount ing
    into wood or wall stud, use #10 x 1¼" wood screws; for mount ing into dry wall
    (minimum ½" thick), use
    3
    /
    16
    " tog gle bolts or
    3
    /
    16
    " molly bolts. DO NOT USE FLAT
    HEAD SCREWS. DO NOT OVERTIGHTEN.
    Use the holes at the front of the endcap/
    mount ing brack et for sus pend ed mount ing.
    Po si tion and prop er ly an chor screw eyes or
    oth er fasteners (not included) into ceil ing
    joists or oth er sol id sur face. Sus pend “S”
    hooks (not included) from fas ten ers (not
    included) and hook through holes in the
    front of the mount ing brack et. For added
    safe ty, crimp both ends of the “S” hooks so
    the screen can not come off.
    Recommended hardware (not included):
    For mount ing into wood or ceil ing joist,
    use two
    3
    /
    16
    " x 1
    1
    /
    4
    " screw eyes and
    3
    /
    16
    "
    di am e ter “S” hooks; for mount ing into
    dry wall (min i mum
    1
    /
    2
    " thick), use
    3
    /
    16
    " tog gle
    or molly bolts with
    3
    /
    16
    " “S” hooks.
    Wall mount the brackets (not in clud ed
    with screen) using hard ware recom-
    mended for “Wall Mounting” (above, not
    included). Then, sus pend the screen from
    the front holes with “S” hooks. For added
    safe ty, crimp both ends of the “S” hooks
    so the screen can not come off.
    DO NOT OVERTIGHTEN.
    ®
    Loosen the clip assembly by turn ing the
    formed steel hanger counterclockwise.
    Spread the clip assembly apart, place over
    the T-irons, and rmly squeeze the clip
    assembly back to geth er, mak ing sure the
    clip is rmly seated around the T-iron.
    Retighten by using pliers to turn the formed
    steel hanger clockwise. Make sure it is fully
    tightened.
    Se cure with the nut. Tighten with pliers.
    Please Note: Make sure the clip is
    fully tightened around the T-iron, and
    that the formed steel hanger and the
    lock nut are fully tightened. Poorly
    tightened clip assemblies, hangers
    or nuts allow the T-Bar Twist Clip to
    work loose.
    Test by trying to pull the twist clip open and by pulling down on the hanger.
    The clip should not pull open.
    Suspend “S” hooks (not included) from the holes in the clips and hook
    through holes in the front of the screen mounting brack et. For added safe ty,
    crimp both ends of the “S” hooks so the screen can not come off.
    Please Note: T–Bar Twist Clips are not rec om mend ed for screens larg er
    than 70" x 70" unless T-irons are reinforced.
    Crimp
    Crimp
    Caution
    Read and understand these instructions; keep them for future reference.
    Follow instructions carefully.
    Care in both mounting and correct operation will mean long and satis-
    factory service from your Draper screen.
    Locate the screen where the audience can best see it, and where other
    room fur nish ings permit.
    Mount the screen so that the bottom of the picture, when screen is fully
    extended, will be above the heads of viewers.
    When raising screen, pull down and, while holding, allow for slow
    retraction into the case to reduce risk of injury from falling screen.
    Screen should be installed level (using a carpenter’s level).
    Nothing should be fastened to screen dowel or viewing surface.
    NOTE: Screen has been thoroughly inspected and tested at factory and found to
    be operating prior to shipment.
    Luma
    Star
    Luma pictured
    Clip
    Assembly
    Screen
    Hanger
    Nut
    Crimp
    Crimp
    Luma pictured
    Viewing Surface Care & Maintenance
    Matt White & High Contrast Grey
    Clean surface with a solution of mild dishwashing liquid diluted with warm
    water. Sponge the surface, rinse with clear water and blot dry. Do not use clean ing
    solvents or abrasives.
    Glass Beaded
    Clean with a very soft brush or cloth and care ful ly dust the surface. DO NOT
    USE SOAP, WATER, SOLVENTS OR ABRASIVES. These substances will damage
    a glass beaded viewing surface.
    Caution: If mounting screen on old-
    style metal wall brackets, do not mount
    back of screen to front of bracket.
    Lip to prevent screen from
    “jumping” off mounting screw
    Please note: When installing wall brackets, fl exible driver bit extensions may make
    it easier to accurately drive the fasteners into the mounting surface.
Draper Luma 207101

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Draper Luma 207101? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Draper Luma 207101 att svara på din fråga.

Se manualen för Draper Luma 207101 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 7. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Draper Luma 207101? Ställ din fråga här

Draper Luma 207101 – specifikationer

Allmänt
Varumärke Draper
Modell Luma 207101
Produkt Projektions skärm
EAN 628261067695, 6410921621552, 6410921622610
Språk Engelsk
Filtyp PDF
Prestanda
Native bildförhållande 16:9
Sammanlagd skärmstorlek (höjd x bredd) 234 x 132
Diagonal 106
Format HDTV
Vikt & dimension
Vikt 11339

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer