Drayton Digistat+3 bruksanvisning

Drayton Digistat+3
(1)
  • Sidantal: 2
  • Filtyp: PDF
  • Drayton

    Installation Guide

    Programmable Room

    Thermostat

    7 Day (5-2 Day)

    Models:

    22083 / 22087

    Power Supply:

    Battery / Mains

    Invensys Controls Europe
    Technical Helpline: +44 (0) 845 130 7722www.draytoncontrols.co.uk
    I
    nstallation / User Guide 06490044001 (0406)

    Drayton

    User Guide

    Programmable Room

    Thermostat

    7 Day (5-2 Day)

    Models:

    22083 / 22087

    Power Supply:

    Battery / Mains

    Invensys Controls Europe
    Technical Helpline: +44 (0) 845 130 7722www.draytoncontrols.co.uk
    I
    nstallation / User Guide 06490044001 (0406)
    Warning
    If you do not have the knowledge to install the Digistat+3 safely,
    arrange for a competent electrician to install it for you. Wiring
    should conform to the current IEE wiring regulations. Isolate
    mains supply before removing an existing room thermostat and
    fitting
    Digistat+3.
    Digistat+3 programmable room thermostats are double
    insulated therefore Neutral and Earth connections are not
    required. Unused existing cables should be safely insulated.
    Location
    Care should be taken to mount the
    Digistat+3 on a wall, in a postion
    which is not subject to direct
    sunlight or draughts. Preferably it
    should be mounted on an inside
    wall about 1.5M (5ft) above the
    floor in a position where it can
    respond to room temperature but
    away from the direct influence of radiators or other appliances
    giving off heat
    .
    Installation
    1.
    Remove the front cover using a flat screwdriver and separate
    from back plate (Fig 1).
    2. Fix the back plate directly onto the wall using suitable wall
    plugs and screws or mount over existing wall box (Fig 2).
    3. Complete the wiring according to the connection suggestions
    shown in Fig 3. For Basic boiler, Combi boiler and Basic boiler
    with zone valve applications Digistat+3 with battery or mains
    supply are suitable. For Electric Heat application use
    Digistat+3 with mains supply only.
    4. Replace the front cover by locating in position and pushing
    fully onto the back cover (Fig 4).
    5. Remove the battery cover using a coin (Fig 5). Battery model only.
    6. Install the 2 AA batteries provided (Fig 6). Battery model only.
    7. Replace battery cover (fig 7). Battery model only.
    8. The Digistat+3 is now installed and will automatically start to
    control the room temperature according to the pre-set
    program 1 as shown in the User Guide.
    The display shows the correct time and date which is
    automatically set together with the actual room temperature.
    Your Digistat+3 programmable room
    thermostat. (7 day (5-2 Day)
    Digistat+3 programmable room thermostat allows you to set
    time and temperature periods (up to 6 per day) to suit your own
    lifestyle. Once fully installed and powered the
    Digistat+3 will
    automatically set the correct time and in auto mode will control
    your heating system according to pre-set program 1 (9 till 5).
    The temperature is controlled by sensing air temperature,
    switching on the heating when the air temperature falls below
    the thermostat setting and switching it off once this set
    temperature has been reached.
    (Fig 1)(Fig 2)
    H
    ow to change the temperature for a short time (Override).
    W
    hen in Auto mode you can override the existing temperature
    s
    etting by pressing + or -. During adjustment the temperature will
    flash then stop. The
    Digistat+3 will now control at this
    t
    emperature until the next programmed time/temperature event is
    r
    eached, when the
    D
    igistat+3
    w
    ill revert back to Auto mode.
    Whilst in temperature override the pointer indicates both Man and
    A
    uto. To exit override press > to return to Auto. (Fig 1) shows
    D
    igistat+3
    i
    n override.
    H
    ow to set a constant room temperature (Manual mode).
    M
    anual mode will allow you to set a temperature, over-riding all
    programs, until you exit manual mode. In this mode all pre-set
    time temperature events will be disabled.
    T
    o enter manual mode press < until the pointer indicates MAN
    (
    Fig 2). The screen will only show the temperature, which can be
    adjusted by pressing + or -.
    O
    nce you have set the temperature it will flash for 5 seconds and
    t
    hen stop. The D
    igistat+3
    w
    ill now control at this temperature until
    you adjust using + or - or exit by pressing > to enter Auto mode.
    (Fig 1)(Fig 2)(Fig 4)(Fig 6)(Fig 7)(Fig 5)(Fig 3)
    TEAR HERE TEAR HERE
    How to set my room temperature for my holiday period.
    (
    Holiday Mode)
    When going on holiday you can lower the temperature of your
    home for the duration of your holiday, but set
    Digistat+3 to
    r
    eturn to your normal programming ready for your return.
    H
    oliday mode works by counting down the days or hour until
    your return.
    T
    ime periods of between 1 to 24hr then 1 day to 199 days can
    be set.
    Example
    I
    am ready to leave for my 2 week (14 day) holiday and would like
    t
    he house temperature held at a constant 10.0 ºC during this time
    and on my return the house temperature will be already running
    at my normal pre-set temperature.
    To enter Holiday mode press the < button until the pointer is
    indicating HOL (fig 3). The temperature will flash and by pressing
    the + or - buttons you can change to the temperature required (
    in this example to 10.0 ºC) (Fig 3a).
    Then press < again to set the time period.(in this example 14
    days) using the + or - buttons. (it would be advisable in this
    example to set the time period 1 day less (13 days) to ensure the
    house temperature is back to normal on your return). (Fig 3b)
    Once you have set your time period the time will flash for 10
    seconds and then start the holiday period. To exit the Holiday
    mode press either < or > to return to auto mode.
    When changing time the display will scroll through Hr (Hours)
    1-24 then d (Days) 1-99.
    The display will show holiday time period and set temperature.
    (Fig 3)(Fig 3a)(Fig 3b)(Fig 4) (Fig 5)Battery Model only.
    How do I know when to change the batteries.
    When the batteries start to run low a battery icon will blink for
    15 seconds every 15 seconds to indicate “low battery” during
    this time the
    Digistat+3 will function normally (see fig 4).
    Please replace batteries with (2 x AA 1.5V Alkaline batteries).
    After 6 months the
    Digistat+3 will cease to function and will
    permanently display the battery icon and nothing else, shown in
    (fig 5).
    (
    Fig 6)(Fig 8)(Fig 7)(Fig 10)(Fig 9)
    H
    ow to change the time, day, month & year.
    Digistat+3 comes with a pre-set clock, which also automatically
    adjusts for summer/winter time changes. It is activated
    a
    utomatically on 1st installation. There should be no need to
    c
    hange these settings, however, should you wish to, it can be
    done in clock mode.
    To enter clock mode press > to select Day. Select Sunday. Use >
    t
    o move through all 6 time/temperature events until the arrow
    p
    oints to the clock symbol. The time will now flash and can be
    adjusted (Fig 7) by pressing + or - then press > to accept and
    m
    ove to Day.
    C
    hange day.
    (
    Fig 8).
    I
    f you wish to change the day press + or - then press > to accept.
    D
    igistat+3
    w
    ill move to the next field - month.
    C
    hange month.
    (
    Fig 9).
    If you wish to change the month press + or - then press > to
    accept.
    Digistat+3 will move to the next field - Year.
    Change year. (Fig 10).
    If you wish to change the year press + or -, then press > to
    accept.
    Digistat+3 will now return to Auto mode.
    H
    ow to replace the batteries see fig 6.
    Remove the battery cover using a coin. Replace the spent
    b
    atteries with 2 x AA 1.5V alkaline batteries ensuring correct
    o
    rientation. Replace the battery cover pressing fully home.
    Display Error code E1 or E2.
    When the display shows E1 or E2 this indicates a sensor fault and
    your heating system will remain Off. Please contact your installer.
    How to select another pre-set time/temperature program.
    There are 3 pre-set time/temperature programs already held in
    memory as shown, if pre-set program 1 is the best program to
    suit your lifestyle do nothing and the
    Digistat+3 will control to
    program 1.
    If you would like to select one of the other pre-set programs,
    refer to ‘How to change User Options’, Option 3 and select your
    preferred program.
    Certification Mark
    06490044001 Digistat+3 update 7/3/06 11:19 am Page 1
Drayton Digistat+3

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Drayton Digistat+3? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Drayton Digistat+3 att svara på din fråga.

Se manualen för Drayton Digistat+3 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 9.3. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Drayton Digistat+3? Ställ din fråga här