Electrolux EWE361LA-DAX4 bruksanvisning

Electrolux EWE361LA-DAX4
(1)
  • Sidantal: 2
  • Filtyp: PDF
EN ELECTRIC WATER HEATER USER MANUALEWE361LA-DAX4EWE361LX-DBX4EWE361LB-DIX4
2. SAFETY INFORMATION
2.1 Products manufactured by Electrolux are safe
provided they are installed, used and maintained
in good working order in accordance with our
instructions and recommendations. Always refer
to this manual if you have any doubt.
2.2 The Electric Water Heater must be earthed.
Improper grounding could cause electrical shock.
2.3 If any of the following conditions occur as
shown below, immediately switch off the power
supply and contact the Electrolux Consumer
2.6 When the Electric Water Heater is
used by someone such as child, elderly
person, sick person and physically
handicapped person, the person
concerned is kindly requested to pay
attention and check the shower
temperature by hand from time to time.
2.7 During lightning/thunder, switch off the power
supply to the Electric Water Heater in advance to protect
the Electric Water Heater against possible damage.
2.8 The earth continuity conductor of the electrical
installation must be effectively connected to all
exposed metal parts of other appliances and
services in the room, which in th
e Electric Water
Heater is to be installed to conform to local
regulations and ensure proper earthing/grounding
for ELCB to be effective.
NOTE: When removing the Electric Water Heater
from package, a small amount of water may be
found inside. This is normal as the Electric Water
Heater is tested during manufacturing process.
WARNING !
.
.
.
.
.
If the Electric Water Heater begins to make an odd noise, smell or smoke.If ELCB trips and Electric Water Heater Indicator does not light up. Water temperature cannot be controlled.If the Electric Water Heater shows signs of a distinct change in performance.If water leaks from inside.
2.10 Installation must be carried out by a
qualified personnel and in compliance local
2.11 This Electric Water Heater must be
permanently connected to the direct main line
supply. A plug and socket is not recommended
to be used.
2.12 For the correct size of wire conductor
corresponding to different electrical loadings,
2.13 T his Electric Water Heater operates at a
minimum water ow rate of 2.0 litre/min and
maximum working pressure of 6 bars. For
direct connection from the water tank, the
2.14
The Electric Water Heater will not function
if there is i
nsufficient water ow (min 2.0 litre/min)
2.15
The built-in ELCB will automatically cut off
the power supply in case there is a current
2.16
The thermostat will automatically cut off the
power supply if it has sensed an abnormal rise in
water temperature.CAUTION !
authority regulations.
please refer to Table 1.
Electric Water Heater must have an
installation minimum 1.0m below the water tank.
to trigger the ow switch.
leakage over 15mA.
Care Center. Never attempt to repair the Electric
Water Heater yourself: 2.5 For Pump Model, it is highly recommended to connect the Water Inlet Connection to tank storage supply, otherwise it may cause damage to the Pump Motor.
User is advised to test and adjust the
water temperature before using.
2.9 WARNING : Metallic / chromed hose and conductive control valve shall not be used.
REV 1
3.
ELECTRIC WATER HEATER UNIT INSTALLATION3.1 Select a suitable position in the bathroom.3.2 Remove the screw (A) at the bottom of the Electric Water Heater. (Fig. 2)3.3 Remove the Front Cover from the bottom and then lift up the front cover.3.4 Mark 3 Screw points of the Heater Base on the wall. The Electric Water Heater position should be 1.5m above the bathroom floor. (Fig. 2)3.5 Mark 2 screw points of the Slider Rail beside the Electric Water Heater. It is recommended that the top of the portion is in level with the top of Electric Water Heater. (Fig. 3)3.6 Use 6mm diameter drill and make the wall plug holes in depth of 34mm ,for mount the Electric Water Heater.3.7 Insert the wall plugs and mount the Electric Water Heater firmly in position with the screws provided.3.8 Insert the Shower Holder and Soap Tray into the Slider Rail. 3.9 Insert the Rail Bracket to both end of the Slider Rail Bar.3.10 Remove the cap from the Rail Bracket and screw the Bracket to marked position. Replace the cap. (Fig. 3)
Fig. 3
connect the
hand shower
to flexible hose
SHOWER SET INSTALLATION DIAGRAM
Flexible Angle
Adjustment
5 Spray
Patterns
Selection
Hand
Shower
Flexible
Hose
Soap Tray
Slider Rail Bar
Adjustable
Shower
Holder
Screw
Wall Plug
Mounting
Terminal
connect to
water outlet
connection
Rail bracket cap
Hexagon tool
(Tighten plastic nut before close cap)
Plastic nut
Fig 3A
RAIL BRACKET COVER & CAP DISMANTLE STEPS
1
RAIL BRACKET
2
OPEN THE RAIL
BRACKET COVER
BY TURNING ANTI
CLOCKWISE &
USING SCREW
DRIVER TO OPEN
THE CAP
3
RAIL BRACKET
COVER COME-OUT
4. PLUMBING PROCEDURE
CAUTION!IMPORTANTThis Electric Water Heater is a single point system and the “Water Outlet” can only be fitted to the Hose and Handshower set provided. MUST NOT TO CONNECT CONTROL VALVE OR FITTING CAN BE FITTED TO THE WATER OUTLET.WARNING!
5.
ELECTRICAL INSTALLATION
WARNING!PROCEDURE :5.7 Connect the cable as following: (Fig. 5)BROWN or RED --LIVE (L)BLUE or BLACK --NEUTRAL (N)GREEN or GREEN/YELLOW --EARTH ( )5.8 Clamp the cable to the correct position.Technician need to confirm the wire before installation. CHECK IF THE WIRING CONNECTION IS CORRECT and replace the cover.5.9 When putting back the Front Cover, please take note of the procedure shown below :-Ensure the position is correct, turn the Temperature Control Knob Insert to OFF position as shown in Fig.A (At the Heater Base)5.1 This Electric Water Heater must be earthed. Improper grounding could cause electrical shock.5.2 Remember to SWITCH OFF the power supply before carrying out any electrical work.5.3 Refer to TABLE 1 for the correct cable size.5.4 Use double insulation cable of over 4.0mm²5.5 Lead the power cable from MCB to a “ON/OFF’’ double pole Linked Switch having a contact separation of at least 3mm in all poles outside the bathroom, then lead a cable to the terminal block inside the Electric Water Heater. (Fig. 4)5.6 Insert the wall embedded cable through Side Entry ‘A’ by cutting a hole at the source cord rubber holder and lead the cable to Cable Bracket ‘B’. (Fig. 6)Always KEEP the water supply to the Electric Water Heater free from mud and dirt at all time during usage.4.1 Connect the 3 in 1 Stop Valve to the Water Inlet with washer. Use correct tools to tighten and be careful not to over tighten and damage the plastic nut.4.2 Connect the incoming water piping to the 3 in 1 Stop Valve (1/2” BSP).Make sure to put the Mesh Filter between 3 in 1 Stop Valve and incoming water piping.4.3 If in any case, the 3 in 1 Stop Valve is not use or omitted, make sure to put the Mesh Filter between the Electric Water Heater inlet pipe and incoming water pipe.4.4 Turn on the water mains to drain out all plumbing dirts before connecting the water supply to the Electric Water Heater, the water supply to the Electric Water Heater must be free from mud and dirt. 4.6 Hook the Handshower to the Slider Rail Shower Holder and adjust to your ideal position.4.7 Check if any water leakage.4.8 Do not use sealing tape during piping installation.THE HEATER TANK MUST BE FILLED UP WITH WATER BEFORE TURNING ON THE POWER SUPPLY TO PREVENT ANY DRY BURNT DAMAGE TO THE HEATING ELEMENT.4.5 Connect the Hose and Handshower to the outlet of Electric Water Heater, be sure to put in the Washer in between the connection. (Fig. 2)4.10 DO NOT APPLY PLUMBING CEMENT ON CONNECTION. WHENEVER NECESSARY, USE ONLY THREAD OR SEALING TAPE.4.9 THE WATER INLET AND OUTLET MUST BE INSTALLED CORRECTLY, OTHERWISE ELECTRIC WATER HEATER WILL NOT FUNCTION.

5. ELECTRICAL INSTALLATION (CONT’D)

6. TABLE 1 - CABLE SIZE TABLE

Power Current (kW) (A) Conductor Size (csa)mm Conduit Cable Flexible Cable On/ Off Fuse / Switch (A) MCB (A)
2
Voltage
(AC)
3.6 15.0 4.0 7 / 0.85mm 56 / 0.30 mm 20 20240V ~50/60 Hz(Malaysia Model)
METHOD OF ALIGNMENT WHEN REPLACING FRONT COVERCableFig. 4Brown or Red = Live (L)Blue or Black = Neutral (N)Green or Green/ Yellow = Earth ( )Fig. 5 Fuse Distributor BoardMiniature Circuit Breaker (MCB)ON/OFF Double Pole SwitchDouble PVC cable NOTE:Refer to TABLE 1 for electrical loading and correct size of wire conductorFront CoverFig AFig B
OFF
A
B
Fig. 6Position this Way
OFF
Position this Way

1 2

3
4
5
9
10
12
13
11
14

1. PARTS IDENTIFICATION

1. Front Cover2. LED Indicators i) Earth LED Indicator ii) Power/ELCB Indicator3.
Test / Reset Button4.
Rating Label5. Pump Button*6. Temperature Control Knob7. 3 in 1 Stop Valve i) Stop Valve Lever ii) Flow Regulator Valve Adjustment iii) Built-in-Filter8. Mesh Filter 9. Rail Support 10.
Handshower11.
Adjustable Shower Holder12. Slider Rail
13.
PVC Hose14.
Soap Tray15. Heater Base16. Terminal Block17. Thermostat (Double-Action)18. Heater Tank19. PCB Board (Test & Reset)20. VR Board21. Main/ ELCB Board**22. Water Outlet Connection23. AC Pump* 24. TRIAC25. Reed Switch Assy26. Water Inlet Connection27. SMPS PCB Board28. D.C. Silent Pump*29. Pump Board30. Temperature Knob LED Light
15
16
18
19
22
21
23
24
25
26
OFF
7
8
27
24
25
26
OFF
7
8
28
No Pump model
24
25
26
OFF
7
8
AC Pump model DC Pump model Fig. 1
15
16
18
19
22
20
21
17
17
15
16
18
19
22
21
17
OFF
7
8
1
3
6
4
29
29
5
*
*
*
2
connect to water outletconnection ELECTRIC WATER HEATER UNIT INSTALLATION DIAGRAMFig. 2Screw
A
3 in 1 stop valve inlet
Wall
285.5mm Washerconnect to water inletconnection
Min.
80 mm150mm OFF* For Pump Model only** Pump Model VR Board & Main/ELCB Board combine.2.4 If the Red (POWER) Indicator does not go offwhen you turn off the water, switch OFF the
mains supply and contact Electrolux ConsumerCare Centre for repair service.Special skill isrequired for repairing. NEVER try to repair the unit by yourself.
* **
* **
**
**
30
-
Install the Front Cover,turn the Temperature
Control Knob to OFF position to align with the
VR shaft as shown in Fig.B (At the Front Cover)
5.10 Fix the Temperature Control Knob and
screw ‘A’ (Fig. 2).
Reconnect the Temperature Knob LED Lightwire to Main Board (J5 Connector).
Electrolux EWE361LA-DAX4

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Electrolux EWE361LA-DAX4? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Electrolux EWE361LA-DAX4 att svara på din fråga.

Se manualen för Electrolux EWE361LA-DAX4 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 7.5. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Electrolux EWE361LA-DAX4? Ställ din fråga här

Electrolux EWE361LA-DAX4 – specifikationer

Allmänt
Varumärke Electrolux
Modell EWE361LA-DAX4
Produkt Vatten värmare och kokare
Språk Engelsk
Filtyp PDF

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Electrolux EWE361LA-DAX4 .

Är din fråga inte listad? Ställ din fråga här