Elro SX32 bruksanvisning

Elro SX32
(1)
  • Sidantal: 1
  • Filtyp: PDF
  • Wire Free Converter

    SX-32

    Battery Installation
    1. The Converter unit is operated by 1 x 12 volt battery (23A - included).
    2. Remove the back of the case by pushing in the tab on the bottom with a
    small, flat screwdriver.
    3. Insert 1 x 12 volt battery (23A - included) in the battery compartment, ensuring
    the battery’s polarity matches the internal markings.
    4. Snap the front cover of push button back on, then it is ready to use.
    Installation Guide
    1) Westminster - 8 notes
    2) Ding-Dong - Repeat
    3) Telephone Ring
    4) Circus Theme
    Melody Selection (On selected Models)
    The Melody selector is located inside the push converter unit, a small switch on the
    top left corner of battery compartment marked with “S”. Press the switch once, the
    melody will change to the netxt one on the list, there are a total of 8 melodies for
    selection. The converter is pre-set to “Westminster” therefore, if no change is
    required, it should not be adjusted.
    5) Banjo on my knee
    6) Twinkle, Twinkle
    7) It’s a small world
    8) Dog Barking
    1. Drill hole and fit wall plug (if fixing to masonry) and screw (self-tapping N3 x 16mm
    screw) to fixing position. Leave a gap of 3mm between the screw head and the wall.
    Locate the keyhole slot on the back of the unit, over the screw.
    Important: Mounting the Converter unit on metal or UPVC doorframes will seriously
    reduce the operating range.
    2. Then use the second hole located at the bottom half of the Converter as a template,
    mark the fixing position for the unit. Drill hole and fit wall plug and secure the Converter
    Unit with the screw (self-tapping N3 x 16mm screw) in position.
    3. Alternatively, use the double-sided self-adhesive pad (included) to attach the converter
    to the fixing position between the bell push and door chime unit.
    Note: When mounting to masonry, fit wall plugs. When mounting to wooden doorframe
    wall plugs are not necessary.
    In case a Transformer (A/C 8v) is used to power the Wired Bell
    Push and Wired Door Chime.
    1. Remove the back of case by pushing in the tab on the botton
    with a small, flat screwdriver.
    2. Disconnect the wire that connected with Wired Door Chime.
    3. Feed the wire via the hole on the back of the Converter,
    connect the wire to the terminal positions marked below.
    4. Snap the front cover of push button back on, then it is ready
    to use.
    Important: Do not connect the Converter unit with any Lighted
    Bell Push.
    Operation
    When the wired Bell Push is pressed, it will activate the
    Converter and transmit a wireless signal for 1 second to the
    Wireless Door Chime, Green LED light will light up as operation
    indication, and the door chime will sound.
    Important
    1. Do not mount the Converter unit onto any metal surface or metal doorframe including UPVC.
    2. Do not expose the unit directly to rain or immerse either in water.
    3. Do not expose the unit to high temperatures or close to fireplace.
    4. Do not leave exhausted batteries in either unit.
    5. Do not connect the Converter unit with any Lighting Bell Push.
    6. Converter is designed for internal use only.
    7. Please dispose of old, defective batteries in and environmentally friendly manner in accordance with the
    relevant legislation.
    8. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.
    9. The unit should not be exposed to dripping or splashing and that no objects filled with liquids.
    10. Replace only with the same or equivalent type battery recommended by the manufacturer.
    Specification
    Converter unit
    Power
    Consumption
    Operating Temperature
    Operating Distance
    Selectable Tone
    Selectable Channel
    : 1 x 12volt 23A battery (included) Replace with Byron SD100 model.
    : 3.0mA - ON
    0.003mA - OFF
    : -10°C to +40°C
    : 100 metres (320 feet approx.) in open field
    : Total eight (8) tones available
    : Total sixteen (16) possible channels
    The unit comes from the factory on a pre-set radio frequency channel.
    However, should you door chime activate intermittently for no reason at all,
    it is possible that a similar unit is operating nearby on the same frequency.
    The encoded frequency of the Converter (transmitter) and Door Chime
    (receiver) can be changed to avoid this problem.
    1. Remove the back of the case by pushing in the tab on the bottom with a small, flat screwdriver.
    2. There is a 4 position dip switch marked 1,2,3,4. Use a small screwdriver to alter the dip switch levers to
    the “On/Off” position, which can be altered to achieve a total sixteen (16) possible channels.
    3. In any combination ensuring it is set to the same code on both Converter and Wireless Door Chime units.
    4. Test to ensure correct operation before final installation.
    Channel Selection
    B+C SWITCH
    A+C 8V/AC
    B+C SWITCH
    SX
    Chime
    unit
    WIREDCHIME
    (Transformer
    operation)
    4
    T
    Converter
    unit
    SX
    Chime
    unit
    WIREDCHIME
    (Transformer
    operation)
    3
    T
    Converter
    unit
    SX
    Chime
    unit
    1
    Converter
    unit
    SX
    Chime
    unit
    WIREDCHIME
    (Battery
    operation)
    2
    Converter
    unit
    Please note that these diagrams are only for reference
    as a guide.
    EACH Wired chime can be wired differently, so if you
    encounter problems, PLEASE CALL THE HELPLINE ON
    0121 5449499
    Wiring Installation
    The Converter is designed to change your existing Wired Bell Push to wirefree.
    1. Simply connect your Wired Bell Push with the cable from Converter to the terminals on your bellpush.
    2. Your Wired Bell Push with Converter is ready to use.
    B and C
    A and C
    A and C
    A and C
    Wired Bell
    Push
    Converter unit
Elro SX32

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Elro SX32? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Elro SX32 att svara på din fråga.

Se manualen för Elro SX32 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 9.9. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Elro SX32? Ställ din fråga här

Elro SX32 – specifikationer

Allmänt
Varumärke Elro
Modell SX32
Produkt Dörrklocka
Språk Engelsk
Filtyp PDF