GE PT9050DFBB

GE PT9050DFBB bruksanvisning

(1)
  • BEFORE YOU BEGIN
    Read these instructions completely and
    carefully.
    IMPORTANT Save these instructions
    for local inspector’s use.
    IMPORTANT Observe all governing
    codes and ordinances.
    Note to Installer – Be sure to leave these
    instructions with Consumer.
    Note to Consumer – Keep these instructions
    for future reference.
    Skill level – Installation of this appliance
    requires a qualified installer or electrician.
    Proper installation is the responsibility
    of the installer.
    Product failure due to improper installation
    is not covered under Warranty.
    Product is for indoor use only.
    Installation Instructions
    27” & 30 Electric Built-In Wall Ovens
    FOR YOUR SAFETY:
    WARNING
    :
    Before beginning the installation, switch power off at the service panel and
    lock the service disconnecting means to prevent power from being switched on accidentally. When the
    service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
    to the service panel.
    Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
    Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
    stand or hang on the oven door.
    Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
    (up to 200°F [93.3°C]) generated by the oven.
    Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
    In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
    MATERIALS YOU MAY NEED
    Junction Box
    Wire Nuts
    Strain Relief Clamp for 1/2” Conduit
    TOOLS YOU MAY NEED
    1/8” Drill Bit and Electric or Hand Drill
    Phillips Screwdriver
    Wire Strippers
    1
    REMOVE PACKAGING MATERIALS
    Failure to remove packaging materials could result in damage to the appliance. Remove all packing
    parts from oven, racks and heating elements. Remove protective film and labels on the outer door
    and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping
    screws securing the oven to the base pad. Open oven door and remove literature pack and oven
    racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation
    process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from
    seperate box and set aside (30” Double Wall Ovens Only).
    2
    PREPARE THE OPENING
    NOTE: If the cabinet does not have a solid bottom, two
    braces or runners must be installed to support the weight
    of the oven. For single ovens, the runners and braces
    must support 200 lbs (91 kg). For double ovens, the
    runners and braces must support 375 lbs. (170 kg).
    NOTE: If marks, blemishes or the cutout opening are
    visible above the installed oven, it may be necessary to
    add wood shims under the runners and front trim until
    the marks or opening are covered.
    NOTE: If the cabinet does not have a front frame and
    the sides are less than ¾” (1.9 cm) thick, shim both sides
    equally to establish the cutout width.
    ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired) into an
    approved junction box. A plug and receptacle is NOT permitted on these products.
    Suitable
    Bracing
    to Support
    Runners
    C
    L
    2" x 4" (5 cm x 10 cm)
    or Equivalent Runners Level
    with Bottom of Cutout
    and Flush with Sides of Cutout
    DESIGN INFORMATION
    SINGLE OVEN INSTALLATIONS
    The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also
    be installed below a countertop or below specified cooktops. See the label on top of the oven for approved
    models.
    DOUBLE OVEN INSTALLATIONS
    A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the
    oven for approved models.
    IMPORTANT: Always refer to individual installation instructions packed with each product for specific
    requirements.
GE PT9050DFBB

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om GE PT9050DFBB? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av GE PT9050DFBB att svara på din fråga.

Se manualen för helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av personer med ett genomsnitt på . Den här manualen är tillgänglig på följande språk: . Behöver du hjälp eller har du en fråga om ? Ställ din fråga här

GE PT9050DFBB – specifikationer

Varumärke GE
Modell PT9050DFBB
Produkt Ugn
Språk Engelsk, Spanska
Filtyp PDF

Relaterade produktmanualer

Ugn GE

Vanliga frågor

Nedan hittar du de vanligaste frågorna om GEPT9050DFBB .

Är din fråga inte listad? Ställ din fråga här

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer