Hobbywing XeRun 3660 SD G2 bruksanvisning

Hobbywing XeRun 3660 SD G2
(1)
  • Sidantal: 1
  • Filtyp: PDF
It’s important to select the FDR/gear ratio properly, as improper FDR/gear ratio may cause you great loss. Therefore, please choose the gear ratio by referring to the following points!
1. Operating Temperature of the Motor
The motor temperature should be lower than 100/212 during the operation. Temperatures above 100 will weaken the magnet and may partly melt the coils and eventually damage the ESC (due to strong
current). Therefore, the most effective way to prevent overheat is to select the right gear ratio. 2. Principle of Gear Ratio Selection
To avoid potential risks such as ESC/motor damage or malfunction caused by overheat, please start with a very small pinion first and check the ESC & motor temperatures regularly throughout the run. This is the only
way to guarantee that your motor won’t overheat. If the motor and ESC temperatures remain stable and low in the running, then you can slowly increase the pinion size while monitoring temperatures to determine
the safe gearing for your vehicle, climate and track condition. Because these elements may change, so please keep monitoring the ESC & motor temperatures to protect your electronics from damage.
(With the motor direction set to CCW), take the graduation/value after "CCW" on the motor case as the starting point when
adjusting the timing. (With the reversed triangle pointing at a value/graduation,) the smaller/bigger the value,
the smaller/bigger the timing. The timing is 40 degrees (as shown in picture 1) when the motor direction is set to CCW.
(With the motor direction set to CW), take the graduation/value after "CW" on the motor case as the starting point when
adjusting the timing. (With the reversed triangle pointing at a value/graduation,) the smaller/bigger the value,
the smaller/bigger the timing. The timing is 20 degrees (as shown in picture 1) when the motor direction is set to CW.
The motor timing is 30 degrees by default (as shown in picture 2). The motor timing should be within 30 to 40 degrees if you
want to activate the Turbo timing. And the timing can be within 20 to 40 degrees if you have no intention to activate the Turbo timing.

Warnings

CAUTIONS
Thank you for purchasing the XERUN 3652/3660 G2, HOBBYWING’s high performance sensored brushless motor! Brushless power systems can be very dangerous, any improper use may cause personal injury and damage to the product and related devices. We strongly recommend reading through this user manual before use. Because we have no control over the use, installation, or maintenance of this product, no liability may be assumed for any damages or losses resulting from the use of this product. We do not assume responsibility for any losses caused by unauthorized modifications to our product.
ATTENTION
ATTENTION
01
06

FDR/Gear Ratio Selection

05

Timing Adjustment

02

Features

07

Assembly/Disassembly

For prolonging the motor life and raising its efficiency, we recommend checking and cleaning the motor regularly. About the frequency, it depends on the times you
use the motor and the track condition. Please refer to the following diagrams to assemble your motor and dismantle it in the reverse order if necessary.
Parts List:

USER MANUAL

XERUN 3652/3660 G2Sensored Brushless Motor
04

Installation & Connection

1. How to Mount the Motor into a RC vehicle
M3 mounting screws (6*M3) are needed here, as the mounting holes are 5mm in depth, so we don’t recommend using the M3 screws
with the length exceeds 8mm to mount the motor into your vehicle.2. How to Connect the Motor to an ESC
There are three power wires coming from the ESC must be soldered to the motor. They are usually color coded as Blue for Wire A, Yellow
for Wire B and Orange for Wire C. When connecting the power wires between the ESC and motor, please make sure that you match ESC
Wire A to Motor Phase A, ESC Wire B to Motor Phase B and ESC Wire C to Motor Phase C (this is very important).
When using a Sensored ESC, make sure the sensor cable is clean and undamaged first and then connect the sensor cable to both the
ESC and the motor in the correct direction.When using a Sensorless ESC, swap any two wires if the motor runs in reverse. 3. Recheck the Installation & Connections Recheck the installation and all the connections before turning on the power.
3100
3800
4300
5100
6100
3100
3800
4300
5100
6100
3200
3600
4300
0.0087Ω
0.0059Ω
0.0052Ω
0.0035Ω
0.0029Ω
0.0087Ω
0.0059Ω
0.0052Ω
0.0035Ω
0.0029Ω
0.0065Ω
0.0056Ω
0.0038Ω
2.9A
3.9A
4.2A
4.7A
5.9A
2.9A
3.9A
4.2A
4.7A
5.9A
3.7A
4.1A
4.7A
192g (6.77oz)
192g (6.77oz)
187g (6.60oz)
192g (6.77oz)
186g (6.56oz)
192g (6.77oz)
192g (6.77oz)
187g (6.60oz)
192g (6.77oz)
186g (6.56oz)
218g (7.69oz)
214g (7.55oz)
218g (7.69oz)
1/10
th
Light-duty SCT
Truck
Monster Truck
1/10
th
Heavy-duty SCT
Truck
Monster Truck
30401050
30401052
30401053
30401054
30401055
30401056
30401058
30401059
30401060
30401061
30401150
30401151
30401152
2-3S
2-3S
2S
2S
2S
2-3S
2-3S
2S
2S
2S
2-3S
2-3S
2S
4
Φ=3.175mm(0.125in)
L=15mm(0.591)
Φ=5mm(0.197in)
L=17mm(0.669in)
Φ=5mm(0.197in)
L=15mm(0.591in)
XERUN-3652SD-3100KV-D3.175-G2
XERUN-3652SD-3800KV-D3.175-G2
XERUN-3652SD-4300KV-D3.175-G2
XERUN-3652SD-5100KV-D3.175-G2
XERUN-3652SD-6100KV-D3.175-G2
XERUN-3652SD-3100KV-D5.0-G2
XERUN-3652SD-3800KV-D5.0-G2
XERUN-3652SD-4300KV-D5.0-G2
XERUN-3652SD-5100KV-D5.0-G2
XERUN-3652SD-6100KV-D5.0-G2
XERUN-3660SD-3200KV-D5.0-G2
XERUN-3660SD-3600KV-D5.0-G2
XERUN-3660SD-4300KV-D5.0-G2
Φ=36mm (1.417in)
L=52.5mm (2.067in)
Φ=36(1.417in)
L=62(2.44in)
03

Specifications

ModelPN
KV
(No-load)No-loadCurrentMotor Diameter& LengthShaft Diameter & LengthPoles Weight ApplicationsLiPoResistance
• Innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented) with low cogging effect and torque pulsation greatly improves control feel around corners.
• Built-in chip for making the motor be easily identified by HOBBYWING ESCs. When pairing it with a HW 1/8th sensored ESC (i.e. XR8 SCT/Plus), the motor can work in the “sensored” mode at all times with great
output linearity after the identification. The Turbo timing is allowed to be activated for higher output.
• Magnetic ring mounted on the rotor protects the motor from signal interference and guarantees its super stability in the “sensored” mode.
• With the mechanical timing adjustable from 20 degrees to 40 degrees, users are able to have different output power. • Turbine design implemented by the rotor accelerates the internal air circulation and reduces heat.
• Rebuild-able design (partially rebuild-able) and screw-less motor case for easy routine maintenance effectively prolong the motor life and raise the motor effficiency.
• CNC machined aluminum housing, high purity copper windings, advanced rotor structure, high-quality alloy steel output shaft, high-precision bearings for high durability and smoothness.
• New-style “U” solder tabs at the bottom of the motor for easy soldering and wiring.
17mm 62mm
4.5mm
Ø5mm
15mm
20.6mm
Ø35.9mm
6-M3
Ø25.4mm
60°
C.C.W
XERUN 3660SD G2XERUN 3652SD G2XERUN 3652/3660SD G2 XERUN 3652/3660SD G2
52.5mm 15mm
4.5 / 2.8mm
Ø5 / Ø3.175mm
Picture 1 Picture 2
Back End Bell x 1PCS
Stator Set x 1PCS
Screws for Fastening
the Back End Bell
2PCS (M2.5*8.0mm)
Rotor x 1PCS

1 2 3 4 5

Mount washers( the wave washer first,
then the flat washer ) Mount the motor rotor Mount the back end bell set
Mount screws forfastening the back end bellPicture of theassembled motor

XERUN 3660SD G2

Brushless Electronic Speed Controller

Sensor wire

Motor B

Motor A

Motor C

• Never leave this product unsupervised when it is powered on. • Ensure all wires and connections are well insulated before connecting the motor to related devices, as short circuit will damage your motor.• Please strictly follow the A-A, B-B and C-C wiring order when connecting an ESC to the motor. • Never allow this product to come in contact with water, oil, fuel or other electro-conductive liquids. If this happens, stop the use of your product immediately and let it dry carefully.• Read through the manuals of all power devices and chassis and ensure the power configuration is rational before using this unit.• Never hit full throttle before installing the pinion, as high speed rotation may cause damage to the motor in circumstances of no load.• Ensure all devices are well connected, in order to prevent poor connection that may cause your vehicle to lose control or other unpredictable issues such as damage to the device.
• Stop using the motor when its shell temperature exceeds 100/212; otherwise the rotor may be
demagnetized and cause irreversible damage to your motor.
Flat Washer x 1Pcs
Wave Washer x 1Pcs

20161215

Hobbywing XeRun 3660 SD G2

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Hobbywing XeRun 3660 SD G2? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Hobbywing XeRun 3660 SD G2 att svara på din fråga.

Se manualen för Hobbywing XeRun 3660 SD G2 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 8.1. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Hobbywing XeRun 3660 SD G2? Ställ din fråga här

Hobbywing XeRun 3660 SD G2 – specifikationer

Njut av enhetens tunna design utan att uppoffra batteritiden. Litiumpolymerbatteriet levererar samma långvariga laddning...
Allmänt
Varumärke Hobbywing
Modell XeRun 3660 SD G2
Produkt Radiostyrda leksaker
Språk Engelsk
Filtyp PDF
Egenskaper
Produkttyp Motor
Brand kompatibilitet Hobbywing
Komponent för Bil
Kompatibilitet -
Hastighetskonstant (Kv) 4300 RPM/V
Poltal 4
Skaftlängd 17 mm
Axeldiameter 5 mm
Produktens färg Svart
Material, hölje Gjuten aluminium
Motor Borstlös motor
Strömtillförsel
Motorns motstånd 0.0038 Ω
Ström utan belastning 4.7 A
Batteri
Batteriteknik Litium Polymer (LiPo)
Vikt & dimension
Motorns längd 62 mm
Motorns diameter 36 mm
Vikt 218 g
visa mer

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Hobbywing XeRun 3660 SD G2 .

Är din fråga inte listad? Ställ din fråga här