Honeywell RTH230B bruksanvisning

Honeywell RTH230B
9.2 · 2
PDF anvisning
 · 4 sidor
Engelsk
anvisningHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Se manualen för Honeywell RTH230B helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 2 personer med ett genomsnitt på 9.2. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Honeywell RTH230B? Ställ din fråga här

Behöver du hjälp?

Har du en fråga om Honeywell och finns inte svaret i manualen?

  • Få uppdateringar om lösningar
  • Få svar på dina frågor

Fråga och svar

Antal frågor: 0

Honeywell RTH230B är en värmeregulator som används för att kontrollera inomhustemperaturen i bostäder och andra byggnader. Den har en LCD-skärm som visar den aktuella temperaturen och användaren kan ställa in önskad temperatur genom att använda knapparna på regulatorn. Honeywell RTH230B har en programmerbar funktion som tillåter användaren att ställa in åtta olika temperaturinställningar för olika tider på dygnet och för varje dag i veckan. Thermostaten har också en funktion som sparar energi genom att automatiskt sänka temperaturen när ingen är närvarande i hemmet eller byggnaden. Denna Honeywell-termostat är enkel att installera och fungerar för flera olika värme- och kylsystem, inklusive värmepumpar och centrala klimatsystem. Den är också utrustad med en batteribackup som garanterar att inställningarna inte försvinner vid strömavbrott. Honeywell RTH230B erbjuder bra prestanda till ett överkomligt pris och passar de flesta hem och byggnader.

Allmänt
VarumärkeHoneywell
ModellRTH230B
Produkttermostat
SpråkEngelsk
FiltypAnvändarmanual (PDF)

Hittar du inte svaret på din fråga i manualen? Svaret kan finnas här nedan i vanliga frågor gällande Honeywell RTH230B.

Var ska man placera termostaten?

Den bästa platsen för termostaten är det rum där du tillbringar mest tid, i många fall vardagsrummet eller köket. Placera termostaten ungefär en och en halv meter över golvet på en innervägg och skyddad från direkt solljus.

Vad är termostatens dödband?

Om din termostat har ett dödband innebär det att systemet är "i vila". Termostaten slås bara på när exempelvis rumstemperaturen avviker mer än 2 ˚C från den inställda temperaturen.

Vad är den idealiska rumstemperaturen?

De flesta tycker att den idealiska rumstemperaturen är mellan 19 och 22 grader.

Är manualen för Honeywell RTH230B tillgänglig påSvenska?

Tyvärr är manualen för Honeywell RTH230B inte tillgänglig på Svenska. Denna manual finns på Engelsk.

Är din fråga inte listad? Ställ din fråga här

Inga resultat