Make sure the mounting surface is strong enough to hold at least
three times of the device weight.
Step1Drill screw holes on the mounting surface as the positioning
map shows, and then put in the expansion bolts.
Step2Attach the camera pedestal to the mounting surface with the
self-tapping screws.
Step3Power up the camera, and then adjust the lens to the ideal
angle.
Step 5
Step 4
Connect your smart phone to your Wi-Fi network, and make sure your
smartphone is connected to Wi-Fi network with 2.4 GHz band, and then
do the following operations to finish adding camera.
Wait for booting to be finished, and then the camera indicator flashes
with green light.
Note:
If the Wi-Fi network has changed or the indicator status goes
wrong, reset the camera, and then do step 5 to add it again.
If you have more than one camera, do step 5 to add them one
by one.
Mounting Surface
Expansion Bolt
Self-tapping Screw
Camera
Positionting Map
This quick start guide is for reference only. Minor difference might
be found in user interface.
All the design and software here are subject to change without
prior written notice.
All trademarks and registered trademarks mentioned are the
properties of their respective owners.
Please visit our website or contact your local service engineer for
more information.
If there is any uncertainty or controversy, please refer to our final
explanation.
About the Guide
-
-
-
-
-
Q: Cannot connect the camera to Internet with Imou App?
Q: The camera failed to boot up, or cannot operate normally?
FAQ
Make sure the camera and your smartphone are connected
to the Internet successfully. If still cannot work, please press
and hold the reset button for 10s to reset the camera, then try
again.
Press and hold the reset button for 10s to reset the camera
and try again.
If still cannot work, please connect the camera to Wi-Fi
network on web page, then add your camera to Imou
account.
Connect the camera to the PC with Ethernet cable,
and set the PC IP to be the same network segment of
camera which is 192.168.1.108 by default, then login to
the web configuration page.
Select Setting > Network > Wi-Fi > Wi-Fi, you will see all
Wi-Fi signal around listed. Double-click your Wi-Fi
name, enter the Wi-Fi password, and then click
Connection.
After camera is connected to Internet, unplug the
Ethernet cable, and then follow the instruction of part
“Operate with Imou App” to try again.
-
-
a)
b)
c)
Q: Can I continue recording when the SD Card is full?
Q: Camera is offline?
Please check the LED indicator status:
If the green light is solid on, check whether your Wi-Fi router
is successfully connected to Internet. If Internet is OK, please
reboot your camera, or reset the camera to factory default
and configure again.
If the red light flashes slowly or solid on, reset the camera to
factory default and configure again.
If still cannot work, we suggest you contacting the aftersales
service.
When the storage is full, the camera will overwrite the oldest
existing records. We suggest you storing your important
recordings regularly.
-
-
Whatsapp
Mail
Facebook
Behöver du hjälp?
Antal frågor: 10
Behöver du hjälp eller har du en fråga om Imou Bullet Lite 4MP? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Imou Bullet Lite 4MP att svara på din fråga.
ulf,
12-1-2021 11:53:15
Inga kommentarer
Vilken spänning (volt) and DC använder kameran ?
Svara på den här frågan
Ted Heinz,
6-1-2021 21:12:34
Inga kommentarer
Kan man ha 2 mobiler till 1 kamera
Svara på den här frågan
Pär Sommer,
5-1-2021 21:38:16
Inga kommentarer
Hej. Jag får inga notiser eller kamerabilder till min mobil när nån kommer inom zonen. Jag har riktigt bra bild i kameran via appen om jag bara kollar. men om nån går förbi så larmar den inte. Har minneskort i kameran.
Svara på den här frågan
Jörgen ,
1-1-2021 08:13:27
Inga kommentarer
Hej jag får inga notiser från händelser från kameran eller larm trots den varit aktiv. Jag ser bild i telefonen men den larmar ej när ngt rör sig
Svara på den här frågan
Kenneth Götskog,
1-12-2020 13:18:53
Inga kommentarer
Har en imou bullet med dubbla antenner. Den spelar in på minneskortet var femte minut. Hur kommer jag in för att radera dessa.?
Svara på den här frågan
Kenneth Götskog,
24-11-2020 13:18:15
Inga kommentarer
Hej har köpt en imou med dubbla antenner. Hur ställer jag in larmet för att ljuda på natten om det kommer någon. Tacksam för svat
Svara på den här frågan
Patrik,
20-11-2020 12:53:34
Inga kommentarer
Hur gör jag för att 2 användare skall kunna logga in/använda produkten.
För hur mycket jag än letar så lyckas jag inte få in funktionerna i min frus telefon.
På ett ställe ska jag godkänna hennes användning men hittar inte var jag godkänner/lägger till hennes profil/användare.
Svara på den här frågan
Patrik,
20-11-2020 12:49:30
Inga kommentarer
2 användare
Svara på den här frågan
Horst,
18-10-2020 09:05:26
Inga kommentarer
En sladd är elkontakt. Vad är den andra sladden för?
Svara på den här frågan
Anders,
18-9-2020 11:49:31
Inga kommentarer
Jag har bytt wifi/internet i huset hur kan jag para ihop kamerorna på enklaste sätt med det nya wifit??
Svara på den här frågan
Om Imou Bullet Lite 4MP
+6
Se manualen för Imou Bullet Lite 4MP helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 7.6. Den här manualen är tillgänglig på följande språk: Engels. Behöver du hjälp eller har du en fråga om Imou Bullet Lite 4MP? Ställ din fråga här
Nedan hittar du de vanligaste frågorna om Imou Bullet Lite 4MP .
Vad är en megapixel?
Antalet megapixlar anger hur många pixlar det finns i sensorn. 1 megapixel motsvarar 1 miljon pixlar. Ju fler pixlar, desto högre är den potentiella bildkvaliteten.
Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.
Vilken spänning (volt) and DC använder kameran ?