Name: Moog Videolarm QODT4-70NA
Brand: Moog Videolarm
SKU: 247653
Rating: 97 (1 reviews)

anvisningMoog Videolarm QODT4-70NA

- 1 -

GENERAL INSTRUCTIONS

1. Remove contents from the box.

2. Remove the existing ceiling tile from the desired location.

3. Insert the loose end of the saftey cord on the dome through the

middle hole on the edge of the housing opening (Figure 1).

Figure 1

4. Align the eyelet on the cord with the hole located on the inside of

the housing tile opening.

5. Insert the 6-32 x 1/2 round Phillips head screw through the

hole and eyelet. Place the star lockwasher and 6-32 hex nut on

the screw and tighten.

6. Fit the 2 x 2 housing tile in the desired location. The housing

tile will rest on the ceiling grid. (Be sure the grid is adequately

supported).

Safety Cord

goes here

PRODUCT INSTRUCTIONS

REVISION DATE: 02-02-2009

81-IN5257-07024

QOD Q-View ObservaDome

QOD(T/C)X-XXXX

CAMERAS VOLTAGE CURRENT POWER

1 24 VAC/VDC 102mA 2.5W

2 24 VAC/VDC 210mA 5W

3 24 VAC/VDC 331mA 7.9W

4 24 VAC/VDC 487mA 10.9W

Use the formula below to select the correct power supply for

cameras connected in parallel (positive to positive, negative to

negative):

Total current for a 24 VAC system:

TOT AL CURRENT = (202mA x total number of cameras)

Note: 202mA is camera plus power supply

CABLE AND POWER GUIDELINES (Detailed info on Page 10)

This chart shows the proper current needed for power supplies for

Q-View™ cameras. Use Class 2 Power only. Input voltage must

be 24 VAC/VDC.

WIRING

1. Make the proper connections to the incoming power. The RED

wire is POSITIVE (+), the BLACK wre is NEGATIVE (-) (For refer-

ence purposes. Polarity is not important in this unit). The GREEN

wire, labeled Ground, is GROUND for VAC or VDC connections.

NOTE: Connect green ground wire to earth ground (metal conduit,

metal stud, etc.)

2. Attach the BNC connectors to the video in.

TA BLE OF CONTENTS

Cable and Power Guidelines 1, 10

cations 1

General Instructions 1

Wiring 1

Camera Adjustment 1

Camera Focusing 1

Camera Settings 2

Completion of Installation 4

NVT Instructions 4

Wa rranty Information 6

Service and Safeguard Information 7

Tr oubleshooting 8

CAMERA ADJUSTMENTS

1. After completing installation of the housing, use the segmented

arms to adjust each camera to the desired viewing location.

2. Once camera adjustments are made, place the dome back into

position to be sure cameras are not touching the inside of the

dome. If any do, adjust until they are clear.

CAMERA FOCUSING

1. Fine focusing:

Fixed Lens: Loosen the set screw in the lens mount and

manually rotate the lens until a clear picture is achieved. Once

the focus is set, retighten the set screw (Figure 2).

Figure 2

Set screw

Fixed lens

Anvisning

Se manualen för Moog Videolarm QODT4-70NA helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 9.7. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Moog Videolarm QODT4-70NA? Ställ din fråga här

Behöver du hjälp?

Har du en fråga om Moog Videolarm QODT4-70NA som inte besvarats i manualen? Ställ din fråga här. Ge en heltäckande beskrivning av problemet och formulera din fråga så tydligt som möjligt. Ju tydligare problemet beskrivs och frågan ställs, desto enklare är det för andra Moog Videolarm QODT4-70NA-ägare att ge dig ett bra svar.

Antal frågor: 0