Name: Moog Videolarm WS2C-50NA
Brand: Moog Videolarm
SKU: 247858
Rating: 58 (1 reviews)

anvisningMoog Videolarm WS2C-50NA

PRODUCT INSTRUCTIONS

INSTALLATION PREPARATION

1. Determine the mounting location. Be sure that you'll be

mounting to a secure wall or ceiling. We also recommend

that for outdoor applications the housing be mounted in a

protected area.

2. Complete all wire and conduit runs prior to installation.

3. The WS2 and WS4 are designed to be mounted in a

standard deep double-gang box.

4. IMPORTANT REMINDER: For outdoor applications it is

strongly recommended that you use sealant. Place a light

bead of sealant around the perimeter of the back of the

housing and around the head of each screw connecting the

housing to the double-gang box.

REVISION DATE: 02-02-2009

Depending on the voltage being used, refer to one of the formulas

below to select the correct power supply for cameras connected in

parallel (positive to positive, negative to negative):

Total current for a 12 VDC system:

TOTAL CURRENT = (350mA x total number of cameras)

Total current for a 24 VAC system:

TOTAL CURRENT = (202mA x total number of cameras)

VOLTAGE CURRENT POWER

12 VDC 350mA 4.2W

24 VAC 202mA 4.8W

CABLE AND POWER GUIDELINES

(Detailed info on Page 12)

This chart shows the proper current needed for power supplies for

Warrior Series cameras. Use Class 2 Power only. Output voltage

must be between 12-28 VDC or 15-28 VAC.

81-IN5236-06154 WARRIOR 2 & 4

WS2(T/C)-XXXX / WS4-XXXX

Figure 1

INSTALLATION PROCEDURE

1. Mount a double-gang box (not provided) using standard proce-

dures. Pull power and video wires through the gang box.

2. Using the security tool provided, loosen the four security

fasteners and remove the housing top.

NOTE: The housing top is held to the base by a lanyard.

3. Remove the bracket assembly by removing the (2) 10-32 screws

(Figure 1).

NOTE: The camera is connected to the power board. Be

careful not to pull the wire loose.

Cable and Power Guidelines 1, 12

Installation Preparation 1

Installation Procedure 1

Wiring 2

Optional Warrior Test Monitor Cable 2

Camera Bracket Setup 2

Camera Focusing 3

Camera Settings 3

Completion of Installation 5

Dome/Window Care 5

NVT Instructions 6

IFS Instructions 7

Warranty Information 8

Service and Safeguard Information 9

Troubleshooting 10

Exploded View WS2 11

Replacement Parts WS2 12

Exploded View WS4 13

Replacement Parts WS4 14

Anvisning

Se manualen för Moog Videolarm WS2C-50NA helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 5.8. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Moog Videolarm WS2C-50NA? Ställ din fråga här

Behöver du hjälp?

Har du en fråga om Moog Videolarm WS2C-50NA som inte besvarats i manualen? Ställ din fråga här. Ge en heltäckande beskrivning av problemet och formulera din fråga så tydligt som möjligt. Ju tydligare problemet beskrivs och frågan ställs, desto enklare är det för andra Moog Videolarm WS2C-50NA-ägare att ge dig ett bra svar.

Antal frågor: 0