Name: Moog Videolarm WS6-50NF
Brand: Moog Videolarm
SKU: 157663
Rating: 58 (1 reviews)

anvisningMoog Videolarm WS6-50NF

PRODUCT INSTRUCTIONS

INSTALLATION PREPARATION

1. Choose an appropriate corner location. The WS6 can be

mounted at any height in a corner.

2. Complete all wire and conduit runs prior to installation of

the housing.

REVISION DATE: 11-11-2010

Depending on the voltage being used, refer to one of the formulas

below to select the correct power supply for cameras connected

in parallel (positive to positive, negative to negative):

Total current for a 12 VDC system:

TOTAL CURRENT = (350mA x total number of cameras)

Total current for a 24 VAC system:

TOTAL CURRENT = (202mA x total number of cameras)

VOLTAGE CURRENT POWER

12 VDC 350mA 4.2W

24 VAC 202mA 4.8W

CABLE AND POWER GUIDELINES

(Detailed info on Page 11)

This chart shows the proper current needed for power supplies for

Warrior Series cameras. Use Class 2 Power only. Input voltage

must be between 12-28 VDC or 15-28 VAC.

81-IN5219 WARRIOR 6

WS6

INSTALLATION PROCEDURE

1. Using the security tool provided, loosen the (3) 10-32 security

fasteners and remove the face plate (Figure 1).

4. Feed the wiring through the conduit knockout. A clamp

connector is included should you desire to use it. Install

the connector so that the nut is on the outside of the housing.

Be sure the hole in the wall is large enough to accommodate

the nut. Tighten the nut securely, making sure that the screw

heads on the connector are in an easy to reach position,

then feed the wiring through the clamp connector.

5. Mount the back box to the wall using appropriate hardware

(not provided).

NOTE: If the clamp connector was used, tighten the screws

at this time. Make sure enough wire is inside

the back box to complete the wiring process.

2. Place the back box into position and mark the four mounting

holes (Figure 2).

3. If you're using the top conduit knockout (Figure 2) REMOVE

THE CAMERA AND BRACKET TO PREVENT DAMAGE.

If using one of the side conduit knockouts it's not necessary to

remove the camera and bracket; however, use caution.

Mounting

Holes

Figure 1

Top conduit knockout behind camera CAMERA MUST BE

REMOVED BEFORE USING

Mounting Holes

Figure 2

Cable and Power Guidelines 1, 11

Installation Preparation 1

Installation Procedure 1

Wiring 2

Optional Warrior Test Monitor Cable 2

Camera Bracket Setup 2

Camera Focusing 3

Camera Settings 3

Completion of Installation 5

Window Guard™ Replacement 5

NVT Instructions 5

Warranty Information 7

Service and Safeguard Information 8

Troubleshooting 9

Anvisning

Se manualen för Moog Videolarm WS6-50NF helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 5.8. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Moog Videolarm WS6-50NF? Ställ din fråga här

Behöver du hjälp?

Har du en fråga om Moog Videolarm WS6-50NF som inte besvarats i manualen? Ställ din fråga här. Ge en heltäckande beskrivning av problemet och formulera din fråga så tydligt som möjligt. Ju tydligare problemet beskrivs och frågan ställs, desto enklare är det för andra Moog Videolarm WS6-50NF-ägare att ge dig ett bra svar.

Antal frågor: 0