Moxa NPort 5650-8-M-SC

Moxa NPort 5650-8-M-SC bruksanvisning

(1)
  • 1 2 3
    P/N: 1802056000211
    NPort 5600 Series Quick
    Installation Guide
    Third Edition, November 2010
    1. Overview
    Welcome to the Moxa NPort 5600 Series. The NPort 5610-8/16
    have 8 or 16 RS-232 ports, the NPort 5630-8/16 have 8 or 16
    RS-422/485 ports, and the NPort 5650-8/16 have 8 or 16
    RS-232/422/485 ports.
    2. Package Checklist
    The NPort 5600 package should contain the following items:
    1 8-port or 16-port serial device server
    NPort Documentation & Software CD
    NPort 5600 Quick Installation Guide
    Optional Accessories:
    CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
    CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
    CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
    CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
    Notify your sales representative if any of the above items is
    missing or damaged.
    3. Hardware Introduction
    The NPort 5600 Series has includes the following models: NPort
    5610-8, NPort 5610-16, NPort 5610-8-48V, NPort 5610-16-48V,
    NPort 5630-8, NPort 5630-16, NPort 5650-8, NPort 5650-8-T,
    NPort 5650-16, NPort 5650-16-T, NPort 5650-8-M-SC, NPort
    5650-16-M-SC, NPort 5650-8-S-SC, and NPort 5650-16-S-SC.
    NOTE
    The wide temperature model does not support LCM display
    panel
    s or push buttons. All of the LCM descriptions below
    apply only to standard temperature models.
    The front and rear panels are shown below:
    Front panel of the NPort 5600 Series
    Rear panel of the NPort 5610/5630/5650 (AC Power)
    Rear panel of the NPort 5650 (Fiber Model)
    Rear panel of the NPort 5610 (DC Power)
    Front panel of the NPort 5650-T Series
    Reset Buttonpress the Reset button continuously for 5 sec to
    load factory defaults: Use a pointed object to press the reset
    button. Release the button after the Ready LED stops blinking.
    LED Indicators on the Front Panelthe front panels of the
    NPort 5600 have several LED indicators, as described in the
    following table.
    Name
    Color
    Function
    Ready
    Off
    Power is off, or power error condition exists.
    Red
    Steady on: Power is on and the NPort is
    booting up.
    Blinking: Indicates an IP conflict, or DHCP or
    BOOTP server did not respond properly.
    Green
    Steady on: Power is on and the NPort is
    functioning normally.
    Blinking:
    The NPort has been located by NPort
    Administrator’s Location function.
    1-16
    Orange
    Serial port is receiving data.
    Green
    Serial port is transmitting data.
    Off
    No data is being transmitted or received
    through the serial port.
    LCM Display PanelIf the NPort is working properly, the LCM
    panel will display a green color. The red Ready LED will also light
    up, indicating that the NPort is receiving power. After the red
    Ready LED turns green, you will see a display similar to:
    N
    P
    5
    6
    1
    0
    -
    6
    1
    9
    2
    .
    1
    6
    8
    1
    2
    5
    4
    This is where
    NP5610-16 is the NPort’s name
    38 is the NPort’s serial number
    192.168.127.254 is the NPort’s IP address
    LCM Panel OperationThere are four buttons on the NPort
    5600’s front panel. These buttons are used to operate the server’s
    LCM panel. Going from left to right, the buttons are:
    Button
    Action
    MENU
    Activates the main menu, or returns to a lower level.
    ︿
    Scrolls up through a list of items shown on the LCM
    panel’s second line.
    Scrolls down through a list of items shown on the LCM
    panel’s second line.
    SEL Selects the option listed on the LCM panel’s second
    line.
    Detailed LCM Panel Operating instructions can be found on the
    CD-ROM in the NPort 5600 Series User’s Manual.
    Link Indicator on the rear panel of the NPort 5650 fiber
    modelthe rear panels of the NPort 5650 have a link indicator, as
    described in the following table.
    LED Name
    LED Color
    LED Function
    Link
    Off
    Fiber disconnected.
    Green
    Fiber connected; data not transmitting.
    Blinking
    Fiber connected; data is transmitting.
    4. Hardware Installation
    STEP 1: After removing the NPort 5600 from the box, the first
    thing you should do is attach the power adaptor.
    STEP 2: Connecting the Power.
    AC: Connect the NPort 5600’s 100-240 VAC power cord to the AC
    connector. The “Ready” LED will show a solid red color until the
    system is ready, at which time it will change to a green color.
    DC: Connect the NPort 5610-16/8-48V’s power cord to the DC
    connector, and then follow the steps given below:
    Loosen the screws on the V+ and V- terminals of
    the NPort 5610-8/16-48V’s terminal block.
    Connect the power cord’s 48 VDC or -48 VDC wire
    to the terminal block’s V+ terminal, and the power
    cord’s DC Power Ground wire to the terminal block’s V- terminal,
    and then tighten the terminal block screws. (Note: The NPort
    5610-8/16-48V can still operate even if the 48V/-48V and DC
    Power Ground are reversed.)
    The “Ready” LED will show a solid red color until the system is
    ready, at which time it will change to a green color.
    Grounding the NPort 5610-8/16-48V:
    Grounding and wire routing help limit the effects of
    noise due to electromagnetic interference (EMI).
    Run the ground connection from the ground
    screw to the grounding surface prior to
    connecting devices. The Shielded Ground
    (sometimes called Protected Ground) contact is
    the second contact from the right of the 5-pin power terminal block
    connector located on the rear panel of the NPort 5610-8/16-48V.
    Connect the SG wire to the Earth ground.
    STEP 3: Connect the NPort 5600 to a network. Use a standard
    straight-through Ethernet cable to connect to a hub or switch.
    When setting up or testing the NPort 5600, you might find it
    convenient to connect directly to your computer’s Ethernet port. In
    this case, use a cross-over Ethernet cable.
Moxa NPort 5650-8-M-SC

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Moxa NPort 5650-8-M-SC? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Moxa NPort 5650-8-M-SC att svara på din fråga.

Se manualen för Moxa NPort 5650-8-M-SC helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 9.6. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Moxa NPort 5650-8-M-SC? Ställ din fråga här

Moxa NPort 5650-8-M-SC – specifikationer

Allmänt
Varumärke Moxa
Modell NPort 5650-8-M-SC
Produkt Server
Språk Engelsk
Filtyp PDF
Tekniska data
RS-485-signaler Data+, Data-, GND
RS-422-signaler GND, RxD+, RxD-, TxD+, TxD-
RS-232-signaler CTS, DCD, DSR, DTR, GND, RTS
Baudhastighet 921.6
Flödeskontroll
Seriella portar 8
Seriellt gränssnitt RS-232/422/485
Isolering 1.5
Datahastighet för Ethernet-LAN 10, 100
Anslutningar
Antal LAN (RJ-45) anslutningar 1
Vikt & dimension
Vikt 3360
Protokoll
Stöd för nätverksprotokoll ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, HTTP, SMTP, SNTP, ARP, PPP, RTelnet, RFC2217
Miljökrav
Temperatur vid drift 0 - 55
Temperaturintervall (förvaring) -40 - 85
Intervall för relativ operativ luftfuktighet 5 - 95
Management features
Lednings Protokoll SNMP V1
Indikation
Länk-/aktivitets-LED
Strömtillförsel
Spänning 100 - 240
Design
Säkerhet UL 60950-1, EN 60950-1
Certifiering CE, FCC, EN 55022 Class A, FCC Part 15 Subpart B Class A, \r
EN 60601-1-2 Class B, EN 55011
Övrigt
Kompatibla operativsystem Windows 98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8 x86/x64, Windows 2012 X64\r
\r
SCO Unix, SCO OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i\r
\r
Linux kernel 2.4.x, 2.6.x, 3.x

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Moxa NPort 5650-8-M-SC .

Är din fråga inte listad? Ställ din fråga här

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer