Phihong POE14-050 bruksanvisning

Phihong POE14-050
(1)
  • Sidantal: 2
  • Filtyp: PDF

POE14-120/137 User Manual

Power over Ethernet and Data Splitter

is designed to accommodate low powered devices

such as wireless access points and IP Telephones. A

recent addition of the POE14-137 has an output DC

voltage of 13.7 for backup battery charging capabilities.

Installation Sequence:

1. Using the appropriate Category 5 or 6 Ethernet

cable, connect the PoE In to the Power Injector

or midspan.

2. Using the same category Ethernet cable,

connect the PoE Out to the input RJ45 jack

located on the device.

3. Insert the DC Power cable from the splitter to

input power adapter on the device.

4. Allow a few moments for the Green LED to light

up assuring that everything is connected.

Input Power

IEEE802.3af compatible, 36-57VDC

Output Power

-033 — 3V -120 — 12V

-050 — 5V -137 — 13.7V

Ethernet

Categories 5, 5e or 6

Input/Output

Connectors

PoE and Data - RJ45

DC Cable - Center Positive Barrel

10mm x 2.1mm x 5.5mm (tips

may be changed)

Safety

CE Certifi ed

Dimensions

94 x 52 x 30mm

(3.7 x 2.0 x 1.2in)

Weight

0.1kg (0.22lb)

Operating

Temperature

0 to +40°C

32 to +104°F

47800 Fremont Blvd.
Fremont, CA 94538, USA
Tel: 1-510-445-0100
Fax: 1-510-445-1678
Email: Poe@phihongusa.com

ADVANCING

POE TECHNOLOGY

Power over Ethernet became the new IEEE standard

in 2003 allowing users to send both power and data

to network devices without modifying their existing

Ethernet based network. By sending power with data

over a Local Area Network, users can now minimize their

need for extensive wiring and electrical power outlets

which has both practical and aesthetic realizations.

Most new devices on the market now designed

to operate on a network will be compliant with the

IEEE802.3af standard; however users who are upgrading

their network do not necessarily need to upgrade their

accessory devices. The dilemma comes as what to do

with all of this non-PoE equipment after installing a PoE

network. Phihong has an answer with the POE14 series.

The POE14 is a small device that will connects to the

network and splits the Power into a DC-DC converter

and passes the data through to the device.

By using your standard Category 5 or above Ethernet

cables, the POE14 can take its power from the network

switch or midspan/power injector if applicable. The

device will then split the power into a desired voltage

and the data will run separately as well. The POE14

comes in 4 standard output voltages so users can fi nd

the one that meets their specifi c needs. The diagram

above shows the basic set up of a POE14 Splitter

connected to a non-poe ready IP camera. The Splitter

is table mounted adjacent to the camera and takes

the power from the Ethernet and divides it into a data

Ethernet and a DC power line to the camera. The POE14

Phihong POE14-050

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Phihong POE14-050? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Phihong POE14-050 att svara på din fråga.

Se manualen för Phihong POE14-050 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 7.5. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Phihong POE14-050? Ställ din fråga här

Phihong POE14-050 – specifikationer

Allmänt
Varumärke Phihong
Modell POE14-050
Produkt Nätverkskort/adapter
Språk Engelsk
Filtyp PDF
Nätverk
Kabelteknik 10/100/1000 Base-T
Efterlever industristandard IEEE802.3af
Strömtillförsel
Strömförsörjning via Ethernet 12.5 V
Vikt & dimension
Produktstorlek (BxDxH) 56 x 100 x 28 mm
Vikt 142 g
Egenskaper
LED-indikatorer Ja
visa mer

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Phihong POE14-050 .

Är din fråga inte listad? Ställ din fråga här