Sharp XEA-106

Sharp XEA-106 bruksanvisning

(1)
  • Installing a Paper Roll
    Always install the paper roll even when you set the
    register for not printing journal or receipt in REG mode.
    1. Push the printer cover forward and detach it.
    2. Place a paper roll in the paper roll cradle so
    that the paper unrolls from the bottom.
    Tax 1
    @/TM
    @/TM
    Tax rate (7.0000%) Min. taxable
    amount ($0.11)
    #/
    SBTL
    Changing Other Settings As Necessary
    Your cash register is pre-programmed so that you
    can use it with minimum setup. To change the initial
    settings, see the appropriate sections.
    Initial Settings
    Departments 1 to 4:
    Taxable 1. Positive (+). Preset price: 0.00
    Departments 5 to 8:
    Non-taxable. Positive (+). Preset price: 0.00
    PLU codes 1-10:
    Assigned to dept. 1. Preset price: 0.00
    PLU codes 11-80:
    Not used
    When you program the tax status for a department,
    tax will be automatically added to sales of items
    assigned to the department according to the
    programmed tax status for the department. You can
    also enter tax manually.
    There are two tax programming methods. The tax
    rate method uses a straight percentage rate per
    dollar. The tax table method requires tax break
    information from your state or local tax offices. Use
    the method which is acceptable in your state. You
    can obtain necessary data for tax programming from
    your local tax office.
    DD
    DD
    D
    For tax table programming, see "programming"
    Tax Rate Programming
    The percent rate specified here is used for tax
    calculation on taxable subtotals. Turn the mode
    switch to the Z/PGM position and use the following
    sequence to program the tax rate:
    9
    #/
    SBTL
    Tax number(1-4)
    @/TM
    R
    @/TM
    Q
    where R and Q represent the following.
    R: Tax rate (0.0000% to 99.9999%) x 10000
    Enter the rate in 6 digits (leading zeros may be
    omitted). If the rate is fractional (e.g., 4 3/8%), it
    should be converted to its decimal equivalent
    (4.375) before entering.
    Q: Minimum taxable amount (0.01 to 99.99) x 100
    Smallest amount for which tax must be collected. In
    some states, sales whose amounts are less than the
    minimum taxable amount are not subject to tax. If
    amounts $0.01 to $0.10 are not taxed, the value of
    Q would be 11 (for $0.11), the lowest of the first
    taxable category.
    Time (2:30 p.m.)
    #/
    SBTL
    #/
    SBTL
    DD
    DD
    D
    Always enter the date in 6 digits. For
    example, enter
    0
    2
    1
    5
    1
    0
    for
    February 15, 2010. If you change the date
    format in the Z/PGM mode, follow the newly
    specified format when setting the date.
    DD
    DD
    D
    •Always enter the time in 4 digits even when
    the hour is in the single digit. For example,
    enter
    0
    6
    3
    0
    for 6:30 a.m.
    • 6:30 a.m. prints as “06-30” and 6:30 p.m.
    prints as “06-30@”.
    Setting the Time
    Turn the mode switch to the Z/PGM position and
    enter the time in 4 digits (“hhmm” format) using the
    24 hour system. Press the
    #/
    SBTL
    key once to continue
    programming or twice to exit the program mode.
    3. Insert three new AA batteries.
    Initializing the Cash Register
    For your cash register to operate properly, you must
    initialize it before programming for the first time.
    Follow this procedure.
    1. Remove the register from its packing carton.
    2. Insert the supplied mode key into the mode
    switch and turn it to the REG position.
    3. Insert the plug into the AC outlet.
    IMPORTANT: This operation must be performed
    without batteries loaded.
    4. The buzzer will sound three times. Now your
    cash register has been initialized. The display
    will show "0.00" with “ ”.
    Installing Batteries
    Batteries must be installed in the cash register to
    prevent data and programmed contents from being
    lost from the memory in case of accidental
    disconnection of the AC cord or power failure. Please
    install three new “AA” batteries before programming
    and operating the cash register. Once installed, the
    batteries will last approximately one year. When it is
    time to replace them, the “l” symbol will appear on
    the display to indicate a low battery voltage. If the
    symbol appears, you must replace them within two
    days.
    Install the batteries according to this procedure with
    the AC cord connected:
    1. Push the printer cover forward and detach it.
    4. When the batteries are properly installed, “
    on the display will disappear. Close the battery
    cover.
    5. Attach the printer cover.
    Thank you for purchasing the SHARP Electronic Cash Register Model XE-A106. Please
    read this manual carefully before operating your machine. Keep this manual for future
    reference. It will help you solve any operational problems that you may encounter.
    For assistance call
    1-800-BE-SHARP
    SHARP ELECTRONIC CASH REGISTER
    MODEL
    XE-A106
    INSTRUCTION MANUAL
    WARNING
    FCC Regulations state that any unauthorized changes or modifications to this equipment not
    expressly approved by the manufacturer could void the user’s authority to operate this equipment.
    Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
    pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
    against harmful interference when the equipment is operated in a commercial environment.
    This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
    in accordance with the instruction manual, may cause harmful interference to radio communications.
    Operation of this equipment in a residential area is likely to cause harmful interference in which case
    the user will be required to correct the interference at his own expense.
    CAUTION
    The socket-outlet shall be installed near the equipment and shall be easily accessible.
    FOR YOUR RECORDS
    Please record below the model number and serial number, for easy reference, in case of loss or theft.
    These numbers are located on the right side of the unit. Space is provided for further pertinent data.
    Model Number_______________________________________________________
    Serial Number_______________________________________________________
    Date of Purchase_____________________________________________________
    Place of Purchase____________________________________________________
    Handling Cautions
    Install the cash register in a location not subject to direct sunlight, unusual temperature
    changes, high humidity, or splashing water.
    Do not operate the cash register with wet hands. Water can cause internal component failure.
    The cash register plugs into any standard wall outlet (120V AC ± 10%). Avoid connecting any
    other electrical devices on the same electrical circuit since such connection could cause the
    cash register to malfunction.
    When cleaning the cash register, use a dry, soft cloth. Never use volatile liquids, such as
    benzine or thinner. Chemicals can discolor or damage the cabinet.
    For protection against data loss, please install three new “AA” batteries before using the cash
    register. However, never forget you must initialize the cash register before installation of
    batteries; otherwise damage to memory contents or malfunctioning of the register will occur. You
    can start operating it only after initializing it and then installing batteries.
    For complete electrical disconnection, pull out the main plug.
    Printed in China
    O(TINSE2598RCZZ) 1
    Getting Started
    For Easy Set-up,
    See “Getting Started”
    View from rear
    View from rear
    2. Open the battery cover next to the paper roll
    cradle.
    3. Insert the paper straight into the paper inlet,
    and press the
    ff
    ff
    f key. The inserted end
    comes out at the printing area.
    4. (For journal printing)
    11
    11
    1Insert the top end of the paper into the
    slit in the take-up spool shaft and fold
    the inserted end toward you.
    22
    22
    2Wind the paper two or three turns.
    33
    33
    3Mount the paper holding plate onto the
    take-up spool.
    44
    44
    4Place the take-up spool on the bearing.
    Date (February 15, 2010)
    #/
    SBTL
    #/
    SBTL
    Put the spool shaft in the larger hole of the paper
    holding plate and push the plate in the direction
    of the arrow.
    5. Attach the printer cover.
    (For receipt printing, step 4 should be omitted.)
    Programming the Tax Rate
    Before you can proceed with registration of sales,
    you must first program the tax that is levied in
    accordance with the law of your state. Your cash
    register comes with the ability to program four
    different tax rates. In most states, you will only
    need to program Tax 1. However, if you live in an
    area that has a separate local tax (such as a Parish
    tax) or a hospitality tax, your register can be
    programmed to calculate these separate taxes.
    In order to program the tax to be collected in
    accordance with the law of your state, you must
    specify the tax rate(s) and minimum taxable
    amount(s).
    Checking the Time and Date
    You can display the time and date to check if they
    are correctly set.
    1. Turn the mode switch in the REG position.
    2. Press the
    @/TM
    key once to display the time.
    3. Press the
    @/TM
    key a second time to display the
    date.
    Setting the Date
    In the Z/PGM mode, enter the date in 6 digits using
    the month-day-year format. Press the
    #/
    SBTL
    key once
    to continue programming or twice to exit the
    program mode.
    DD
    DD
    D
    Before placing a new paper roll in the paper
    roll cradle, cut off the pasted (taped) part of
    the paper and confirm that the cut end of the
    paper is straight.
    Maintenance
    Batteries
    This cash register provides a low battery symbol
    (l) and a no battery symbol ( ) which appears on
    the far left of the display in one of the following
    situations:
    Low battery symbol (l)
    • When the voltage of the batteries installed in the
    cash register is under the required level.
    No battery symbol ( )
    • When three batteries are not installed in the cash
    register.
    • When the batteries installed in the cash register
    are dead.
    When either of these symbols appear, check
    batteries. If no batteries are installed, install three
    new “AA” batteries at once. If batteries are already
    installed, replace them with new ones as soon as
    possible. If the AC power cord is disconnected or a
    power failure occurs when the batteries are dead
    or not installed, all the programmed settings will be
    reset to the default settings and any data stored in
    memory will be cleared.
    DD
    DD
    D
    If the low battery symbol appears while
    making a transaction, complete the
    transaction before replacing the batteries.
    C
    Improper use of batteries could cause them to burst
    or leak, which might damage the interior of the cash
    register. Please take the following precautions:
    •Be sure that the positive (+) and negative (-) poles
    of each battery are oriented properly.
    •Never mix batteries of different types.
    •Never mix old batteries and new ones.
    •Never leave dead batteries in the battery
    compartment.
    •Remove the batteries if you plan not to use the cash
    register for long periods.
    •Should a battery leak, clean out the battery
    compartment immediately, taking care not to let the
    battery fluid come into direct contact with your skin.
    •If an incorrect battery is used, it may explode or
    leak.
    •For battery disposal, follow the relevant law or
    regulation in your country.
    Replacement
    1. Be sure the cash register is plugged in.
    2. Turn the mode switch to the REG position.
    6. Check that the “ ” symbol has disappeared.
    7. Close the battery cover.
    8. Replace the printer cover.
    C
    Improper use of batteries could cause them
    to burst or leak, which might damage the
    interior of the machine. See the cautions in
    the "Getting Started" section.
    Paper Roll
    When colored dye appears on the edges of the
    paper roll, it is time to replace the roll. Use paper
    of 2 1/4" (57 mm) in width. To prevent jamming be
    sure to use paper specified by SHARP.
    Replacement (Journal printing)
    1. Turn the mode switch to the REG position.
    2. Open the printer cover.
    3. Press f to advance the paper by several
    lines and then cut the paper to remove the
    take-up spool from the bearing.
    5. Install three new “AA” batteries into the
    battery compartment.
    SHARP ELECTRONICS CORPORATION
    Sharp Plaza, Mahwah, New Jersey 07495-1163
    1-800-BE-SHARP
    http://www.sharpusa.com
    Drawer Handling
    Locking the Drawer
    Develop the habit of locking the drawer when not
    using the register for any extended period of time.
    To lock: Insert the key into the drawer lock and
    turn it 90 degrees counter-clockwise.
    To unlock: Insert the key into the drawer lock and
    turn it 90 degrees clockwise.
    Removing the Drawer
    To remove the drawer, pull it out and lift it up.
    DD
    DD
    D
    • To prevent burglary, it is a good idea to
    empty the drawer after work and leave it
    open at the end of the day.
    • Coin case is detachable. Also the
    separators of the coin case are
    removable.
    Manually Opening the Drawer
    In case of a power failure or if the machine is out of
    order, locate the lever at the bottom of the machine
    and move it in the direction of the arrow to open
    the drawer. The drawer will not open if it is locked
    with the drawer lock key.
    Coin case
    View from rear
    4. After cutting the existing paper, remove the
    paper roll. Then remove the remaining paper
    by pressing
    f .
    5. Remove the paper holding plate from the
    spool.
    View from rear
    4. Open the battery cover and remove the old
    batteries.
    6. Remove the used journal paper roll (if used)
    from the take-up spool.
    7. Install a new paper roll, the paper holding
    plate and the take-up spool according to the
    instructions in "Getting Started."
    C
    In the case of receipt printing, steps 3, 5 and
    6 should be omitted and the paper holding
    plate and the take-up spool need not be
    installed in step 7.
    Replacing the Ink Roller
    1. Open the printer cover.
    2. Remove the ink roller by pulling it upward.
    3. Install a new ink roller.
    4. Close the printer cover.
    Installing the Mounting
    Bracket
    A
    A
    B
    B
    How to attach the mounting bracket
    1.Thoroughly clean the table surface where you
    wish to place the bracket (B).
    2.Peel off the release paper of the adhesive tape
    on the bracket.
    3.Hook the bracket onto the hook (A) at the
    bottom of the back of the register.
    4.Hold down the bracket so that it firmly sticks to
    the table surface.
    How to release the register from the mounting
    bracket
    Lift up the front of the register and pull it towards
    you.
    A mounting bracket which prevents the register
    from moving accidentally is supplied with your
    XE-A106 register. Attach the bracket to a table
    where the register rests, as follows:
    Specifications
    Model:
    XE-A106
    Size:
    Inches: 13.0 (W) x 14.3 (D) x 9.21 (H)
    Millimeters: 330 (W) x 363 (D) x 234 (H)
    Weight:
    Approx. 11.0 lbs. (5.0 kg)
    Power Source:
    120V AC±10%, 60Hz
    Power Consumption:
    Stand-by: 4 W, Operating: 12.5 W
    Working Temperature:
    32 to 104˚F (0 to 40˚C)
    Display:
    LED (Light-Emitting Diode) numeric display
    Printer:
    1 station, print wheel selective type
    Printing Capacity:
    Max. 13 characters
    Paper Roll:
    Width: 2 1/4"
    + 1/64" (57.5mm + 0.5mm)
    Max. external diameter: 3-5/32" (80mm)
    Min. internal diameter: 15/32" (12mm)
    Cash Drawer:
    4 slots for bills, 5 for coins
    Accessories (supplied):
    Paper roll: 1 roll
    Mode key: 1
    Drawer lock key: 1
    Instruction manual (English): 1 copy
    Instruction manual (Spanish): 1 copy
    Quick Start Guide (English): 1 copy
    Quick Start Guide (Spanish): 1 copy
    Ink roller: 1 (installed)
    Take-up spool: 1
    Paper holding plate: 1
    Mounting bracket: 1
    • Specifications and appearance are subject to
    change without notice for improvement.
    Before Calling for Service
    If you encounter any of the following problems,
    please read below before calling for service.
    The display shows symbols that do not make
    sense.
    • Has the machine been initialized properly as
    shown in “Getting Started”?
    The display will not illuminate while the
    machine is turned on. The machine will not
    operate when any key is pressed.
    • Is the power supplied to the electrical outlet?
    (Plug another electrical device into the outlet for
    confirmation.)
    • Is the power cord firmly connected to the
    electrical outlet?
    The display is illuminated, but the machine will
    not accept key entries.
    • Is the mode switch properly set to the REG
    position?
    • Has the machine been initialized properly as
    shown in “Getting Started”?
    Journal paper will not feed properly in the printer.
    • Is the take-up spool installed properly?
    • Is there a paper jam?
    • Is the journal format selected in the printing
    format programming?
    (If the receipt format is selected, the paper is not
    wound around the take-up spool.)
    Printing is faded or illegible.
    • Is the ink roller used up?
    • Has the ink roller been installed properly?
    Lever
    Push this part in the direction of the
    arrow to remove paper holding plate.
    END-USER LIMITED WARRANTY
    Model Specific Section (Carry-in Service)
    Your Product Model Number & Description:
    XE-A106 Cash Register
    (Be sure to have this information available when you need
    service for your product.)
    Warranty Period for this Product:
    One (1) Year Parts and 90 Days labor from date of purchase
    Additional Item(s) Excluded from
    Warranty Coverage (if any): Any consumable items such as paper supplied with the Product.
    Where to Obtain Service:
    From a Sharp Authorized Servicer located in the United States.
    To find the location of the nearest Sharp Authorized Servicer,
    call Sharp toll free at 1- 800-BE-SHARP.
    What to do to Obtain Service:
    Ship prepaid or carry in your Product to a Sharp
    Authorized Servicer. Be sure to have
    Proof of Purchase
    available. If you ship the Product, be sure it is insured and
    packaged securely.
    TO OBTAIN PRODUCT INFORMATION, CALL 1-800-BE-SHARP OR VISIT www.sharpusa.com.
    SHARP ELECTRONICS CORPORATION warrants to the first end-user purchaser (the “Purchaser”) that this Sharp
    brand product (the “Product”), when new and shipped in its original container, will be free from defective
    workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective
    Product or part thereof with a new or remanufactured equivalent at no charge to the Purchaser for parts or labor for
    the period(s) set forth below.
    This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth
    below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper
    voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or
    construction.
    In order to enforce the rights under this limited warranty, the Purchaser should follow the steps set forth below and
    provide proof of purchase to the servicer.
    To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and exclusive of, all
    other warranties, express or implied. Specifically, ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH
    ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF
    MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY
    EXCLUDED. If, under applicable warranties is limited to the period(s) from the date of purchase set forth below.
    Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
    described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of
    Sharp.
    The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole
    and exclusive remedy available to the Purchaser. Correction of defects, in the manner and for the period of time
    described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the Purchaser
    with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence,
    strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects
    in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized
    servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or
    property damage. Some states do not allow limits on warranties or on remedies for breach in certain transactions; in
    such states, the limits herein may not apply.
    3. Pull the printer cover upward and detach it.
Sharp XEA-106

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Sharp XEA-106? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Sharp XEA-106 att svara på din fråga.

Se manualen för Sharp XEA-106 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 8.1. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Sharp XEA-106? Ställ din fråga här

Sharp XEA-106 – specifikationer

Allmänt
Varumärke Sharp
Modell XEA-106
Produkt Kassaapparat
EAN 74000049505
Språk Engelsk
Filtyp PDF
Tekniska data
Clerk lås
Typer av betalning Cash
Antal kontorister / avdelningar 4
Antalet Pris look-up-koder (Plus) 80PLUs
Skrivarteknologi
Stöds pappersbredd 57.5
Utskriftsteknologi Drum-serie
Display
Displaytyp LED
Visa siffror 13siffror
Övrigt
Produktstorlek (BxDxH) 330.2 x 363.2 x 233.7
Vikt & dimension
Vikt 4990
Strömtillförsel
AC-inspänning 120

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer