Upvel US-8G bruksanvisning

Upvel US-8G
(1)
  • Sidantal: 1
  • Filtyp: PDF

5 port Ethernet switch Upvel US-5G

8 port Ethernet switch Upvel US-8G

Package contents

US-5G / US-8G switch

Power adapter

Installation guide, warranty cert.

Requirements

A computer with a network adapter installed

Cat.5, Cat.5e or Cat.6 network cable

The surface must support at least 225g for the switch

The power outlet should be within 1.8m (6 ft) of the switch
Visually inspect the DC power jack to make sure that it is securely connected to the power

adapter

Make sure that there is proper heat dissipation from the switch and adequate ventilation

around the switch

Do not place heavy objects on the switch

Hardware installation

Specifications

1. Connect the power adapter cable to the
power plug. Then plug in the power adapter
(note that the characteristics of the power
outlet must be relevant to the specifications
on the power adaptor sticker).
2. Connect the
network interface of your
computer with any port of the switch via
network cable (UTP cat. 5, 5e or 6).
Model
US-5G
US-8G
Standards
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3x Flow Control
IEEE 802.3ab 1000BASE-T
Cables
Ethernet: cat. 5, up to 100 m.
Fast /Gigabit Ethernet: cat. 5, 5e
or 6, up to 100 m.
Data Rates
(half-duplex /
duplex mode)
Ethernet: 10 / 20 Мbps
Fast Ethernet: 100 / 200 Мbps
Gigabit Ethernet: 1 / 2 Gbps
Switching
Capacity
10 Gbps 16 Gbps
Forwarding Rate
10BASE-T: 14880pps/port
100BASE-TX: 148800pps/port
1000BASE-T: 1488000pps/port
LEDs
Topology
Star

Power

Green: Power is on
Not Illuminated: Power is off

Link/ACT

Green (Solid): Connection for the port is
100/200Mbps (half/full) or 10/20(half/full)
Green (Blinking): Activity is occurring
Not Illuminated: No activity is detected

1000Mbps

Green (Solid): Connection for the port is 1 / 2
Gbps (half/full)
Green (Blinking): Activity is occurring
Not Illuminated: No activity is detected or 1 / 2
Gbps is not supported
Interfaces q-ty
5 ports
8 ports
Interface type
Auto-Negotiation RJ45 ports
(Auto MDI/MDIX)
Switching table
4000 entries for each device
connected
Power
Consumption
2.8 watts (max)
3.2 watts
(max)
Status LEDs
Power, Link/ACT, 1000Mbps
Power adapter 12 V DC 500 mА
Temperature
~ 50° C (32° ~ 122° F)
Humidity
Max. 90% (non-condensing)
Certification
CE, FCC, Rostest
If you still encounter problems or have any questions
regarding the US-5G / US-8G, please contact UPVEL
Technical Support Department.
support@upvel.com
Toll Free Support Hotline:
USA/Canada: 1 (800) 457-381

UPVEL

Los Angeles, CA USA

UPVEL is registered Trademark
Designed in USA / Made in China
The status LEDs remain inactive after plugging in the power adapter.
1. Make sure the connector of the power cable is connected properly and the adapter plug is connected to a
power outlet with the
characteristics relevant to the specifications on the power adaptor sticker. Make sure
the power cable is undamaged.
2. Check for the electric potential in the outlet (e.g. with an electrician's screwdriver).
After connecting computers to a switch the
Internet access is enabled only from one of
them. This switch is not designed to share the
Internet connection

between multiple computers

with no means of other network devices.
After connecting computers to a switch there are problems with sharing files in a network.
1. Check the LEDs on the Switch. Make sure the Link/ACT LED is on.
2. Make sure your network cables are undamaged and are of 1.5 to 100 meters length.
3. Try to disable all of your firewalls.
4. Make sure that file sharing feature of the operating system is enabled and configured. Please refer to
documentation of support of the OS you use.
Which port is the Uplink port?
Since all the ports on the Switch are Auto-MDIX,
any of the ports can be used as an uplink port.
Upvel US-8G

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Upvel US-8G? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Upvel US-8G att svara på din fråga.

Översikt

Se manualen för Upvel US-8G helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 10. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Upvel US-8G? Ställ din fråga här

Upvel US-8G – specifikationer

Allmänt
Varumärke Upvel
Modell US-8G
Produkt Brytare
Språk Engelsk
Filtyp PDF
Management features
Switch-lager -
Switch typ Ohanterad
Anslutningar
Antal grundläggande RJ-45 Ethernet-portar 8
Typ av grundläggande RJ-45 Ethernet-portar Gigabit Ethernet (10/100/1000)
Antal Gigabit Ethernet (koppar)-portar 8
Nätverk
Koppar Ethernet-kablar teknik 100BASE-T,100BASE-TX,10GBASE-T
Kommunikationsstandarder IEEE 802.3,IEEE 802.3ab,IEEE 802.3u,IEEE 802.3x
Full duplex Ja
Flödeskontroll Ja
Auto MDI / MDI-X Ja
10G stöd Nej
Data transmission
Adresstabellstorlek 4000 poster
Switch kapacitet 16 Gbit/s
Jumbo Frames stöd Ja
Design
Rackmontering Nej
Produktens färg Svart
LED-indikatorer Ja
Material, hölje Metall
Certifiering CE, FCC
Staplingsbar -
Strömtillförsel
Ingående ström 0.5 A
Övrigt
Spänning 12 V
Power over Ethernet (PoE)
Strömförsörjning via Ethernet (PoE) stöd Nej
Miljökrav
Temperatur vid drift 0 - 50 ° C
Vikt & dimension
Bredd 74 mm
Djup 138 mm
Höjd 25 mm
Vikt 277 g
visa mer

Vanliga frågor

Nedan hittar du de vanligaste frågorna om Upvel US-8G .

Är din fråga inte listad? Ställ din fråga här