Yamaha VXS8

Yamaha VXS8 bruksanvisning

(1)
  • PLEASE READ CAREFULLY BEFORE PROCEEDING
    * Please keep this manual in a safe place for future reference.
    WARNING
    Always follow the basic precautions listed below to avoid the possibility of
    serious injury or even death from electrical shock, short-circuiting, damages,
    fire or other hazards. These precautions include, but are not limited to, the
    following:
    This device contains no user-serviceable parts. Do not open the device or attempt
    to disassemble the internal parts or modify them in any way. If it should appear to
    be malfunctioning, discontinue use immediately and have it inspected by qualified
    Yamaha service personnel.
    CAUTION
    Always follow the basic precautions listed below to avoid the possibility of
    physical injury to you or others, or damage to the device or other property.
    These precautions include, but are not limited to, the following:
    Do not place the device in an unstable position where it might accidentally fall over.
    Do not place the device in a location where it may come into contact with corrosive
    gases or salt air. Doing so may result in malfunction.
    Do not place the device where it is always exposed to water. Doing so may result in
    malfunction.
    Do not place the device where it is exposed to oil. Doing so may result malfunction.
    Construction work should be carried out in accordance with construction-related
    law and always by a professional constructor. If the device installation requires
    construction work, make sure to observe the following precautions.
    - Choose mounting hardware and an installation location that can support the
    weight of the device.
    - Avoid locations that are exposed to constant vibration.
    - Use the required tools to install the device.
    - Inspect the device periodically.
    Before connecting the device to a power amplifier, turn off the power for all devices.
    Before turning the power on or off for all devices, set all volume levels to minimum.
    Use only speaker cables for connecting speakers to the speaker connectors. Use of
    other types of cables may result in fire.
    Do not wipe the outer packaging with benzine, thinner, or synthetic detergent and
    do not use electrical contact cleaner. These may damage the outer packaging and
    dissolve the parts.
    Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into holes of
    the grille. If this happens, have the device inspected by qualified Yamaha service
    personnel.
    Do not operate the device if the sound is distorting. Prolonged use in this condition
    could cause overheating and result in fire.
    When choosing a power amplifier for use with this device, make sure that the output
    power of the amplifier is lower than the power capacity of this device (see
    SPECIFICATIONS).
    Even if the output power of the amplifier is lower than the power capacity of this
    device (PGM), use of excessive input signals resulting in clipping may cause
    damage to the device.
    Malfunction or fire may occur especially when the following sounds or noises are
    generated:
    - feedback, when using a microphone
    - continuous and extreme volume sound from a musical instrument
    - extreme continuous distorted sound
    - noise caused by plugging/unplugging the cable while the amplifier is turned on
    PRECAUTIONS
    Do not open
    Location
    Connections
    Maintenance
    Handling caution
    NOTICE
    To avoid the possibility of malfunction/damage to the product or damage to other
    property, follow the notices below.
    ƔHandling and Maintenance
    Do not place vinyl, plastic or rubber objects on the device, since this might discolor
    the panel.
    When cleaning the device, use a dry and soft cloth. Do not use paint thinners,
    solvents, cleaning fluids, or chemical-impregnated wiping cloths.
    Condensation can occur in the device due to rapid, drastic changes in ambient
    temperature-when the device is moved from one location to another, or air
    conditioning is turned on or off, for example. Using the device while condensation is
    present can cause damage. If there is reason to believe that condensation might
    have occurred, leave the device for several hours until the condensation has
    completely dried out.
    Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS),
    particularly when connecting speakers in parallel. Connecting an impedance load
    outside the amplifier’s rated range can damage the amplifier.
    When connecting the speakers with high impedance, be sure that the output total of
    each speaker does not exceed the rated output of the power amplifier.
    When using a high-impedance speaker connection, make sure the audio signal is
    passed through an 80 Hz or above high-pass filter before being input to the
    speakers. For VXS5/VXS5W, UL Listing is void without this connection.
    ABOUT THE PROTECTION CIRCUIT
    This speaker system has an internal protection circuit that shuts off the speaker unit
    when an excessive input signal is applied.
    If the speaker unit emits no sound, reduce the volume level of the amplifier
    immediately.
    The sound will return automatically in several seconds.
    Place the speaker on a flat and smooth surface.
    Do not place the speaker on the ground with the grille faced down.
    Do not touch the speaker driver unit.
    ƔAbout This Manual
    The illustrations as shown in this manual are for instructional purposes only, and may
    appear somewhat different from those on your device.
    Yamaha cannot be held responsible for damage caused by improper use or
    modifications to the device.
    Information for Users on Collection and Disposal of Old Equipment
    This symbol on the products, packaging, and/or accompanying
    documents means that used electrical and electronic products should not
    be mixed with general household waste.
    For proper treatment, recovery and recycling of old products, please take
    them to applicable collection points, in accordance with your national
    legislation and the Directives 2002/96/EC.
    By disposing of these products correctly, you will help to save valuable
    resources and prevent any potential negative effects on human health and the
    environment which could otherwise arise from inappropriate waste handling.
    For more information about collection and recycling of old products, please contact your local
    municipality, your waste disposal service or the point of sale where you purchased the items.
    [For business users in the European Union]
    If you wish to discard electrical and electronic equipment, please contact your dealer or
    supplier for further information.
    [Information on Disposal in other Countries outside the European Union]
    This symbol is only valid in the European Union. If you wish to discard these items, please
    contact your local authorities or dealer and ask for the correct method of disposal.
    UNPACKING
    Unpack the contents and confirm that all the following items are included.
    Speaker × 2
    Bracket base × 2
    Mounting bracket × 2
    Bracket cover × 2
    Screw for attaching the mounting bracket × 4 (VXS8/VXS8W: M6, VXS5/VXS5W: M5)
    Stopper screw × 2 (M3, VXS8/VXS8W only)
    Bolt with hexagon hole × 2
    Safety wire × 2
    Terminal cover × 2
    Safety pin × 2
    Hexagon wrench × 1
    Owner’s Manual (this manual)
    * Screws/bolts to fasten the bracket base onto the wall/ceiling and speaker cables are not included.
    SPECIFICATIONS
    *1: Half-space (2π)
    *2: Calculated based on power rating and sensitivity, exclusive of power compression.
    *3: When connecting with low impedance
    *4: IP34 when installing the speaker to the ceiling vertically.
    The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual
    may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since
    specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.
    The dimensions are shown overleaf.
    VXS8/VXS8W VXS5/VXS5W
    Type 2-way, Bass-reflex
    Component LF 8" (20 cm) Cone driver 5-1/4" (13 cm) Cone driver
    HF 1" (2.5 cm) Soft dome tweeter 3/4" (2 cm) Soft dome tweeter
    Coverage angle (500 Hz – 4 kHz on average) 100° H × 100° V 120° H × 120° V
    Nominal impedance 8 Ω
    Power rating NOISE 90 W 75 W
    PGM 180 W 150 W
    MAX 360 W 300 W
    Sensitivity (1W, 1m) *
    1
    91 dB SPL 89 dB SPL
    Maximum SPL (Calculated, 1m) *
    2
    117 dB SPL 114 dB SPL
    Frequency range (-10 dB) *
    1,
    *
    3
    51 Hz – 20 kHz 62 Hz – 20 kHz
    Crossover frequency 2.8 kHz 3 kHz
    Connector Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-)
    Max. wire size 12 AWG (2.5 mm
    2
    )
    Transformer taps 70 V 60 W, 30 W, 15 W, 7.5 W 30 W, 15 W, 7.5 W, 3.8 W
    100 V 60 W, 30 W, 15 W 30 W, 15 W, 7.5 W
    Overload protection Full-range power limiting to protect network and transducers
    Magnetically shielded No
    Dust and water resistant *
    4
    IP35
    Enclosure Shape Rectangle
    Cabinet material ABS
    Baffle material PC/ASA
    Grille material Powder coated perforated aluminum (t=1 mm)
    Aperture ratio: 51%
    Finish VXS8/VXS5: Black (Not painted, approximate value: Munsell N3)
    VXS8W/VXS5W: White (Not painted, approximate value: Munsell 9.3)
    Dimensions (Speaker only)
    (W × H × D in vertical cabinet orientation)
    278 × 430 × 239 mm
    (10.9" × 16.9" × 9.4")
    176 × 280 × 163 mm
    (6.9" × 11.0" × 6.4")
    Net weight (Speaker only, 1 piece) 8.2 kg (18.1 lbs) 3.6 kg (7.9 lbs)
    Packaging Packaged in pair
    INSTALLING THE SPEAKERS
    Install the speakers onto the wall/ceiling with the supplied brackets. Ensure
    that the wall/ceiling is sufficiently strong.
    Illustrations in this manual are for the VXS5. The installation method is the
    same for other models.
    Pre-installation (Preparation of the cable)
    Use stranded wire for cables attached to the Euroblock connector. Strip
    their insulation as shown in the figure and connect them.
    NOTE
    Do not plate stranded wires by solder. Doing so will cause the wire to break.
    An installed speaker is shown below. Install the bracket base and attach the
    mounting bracket as shown.
    NOTE
    When installing the speaker to the ceiling with the grille parallel to the
    ground, install the speaker horizontally.
    When installing the speaker to the ceiling, be sure to install the bracket
    base with its shaft facing horizontally, and not inclined to the ground.
    Mounting bracket is made to not turn left or right when installing the
    speaker to the ceiling.
    1 Put the bracket base onto the wall/ceiling and mark the position for
    the screws/bolts and cables. The diameter of the screw/bolt holes at
    the four corners is M6, and speaker cables hole at the center is
    ø11 mm.
    2 Make holes through the wall/
    ceiling for the bolts and cables,
    as required, and feed the bolts
    and cables from the amplifier
    through the holes, as shown.
    3 Install the bracket base onto
    the wall/ceiling. Make sure to
    fasten four corners of the
    bracket base.
    4 Pass cables through the gap at
    the lower part of the bracket
    cover, and put the bracket
    cover on the bracket base.
    NOTE
    If you want to adjust the slack of
    cables last, the bracket cover
    can be attached after step 5-6.
    Installing to the wall Installing to the ceiling
    VerticalHorizontal
    1
    INSTALL THE BRACKET BASE ONTO THE WALL /CEILING
    About 7 mm (0.3 in.)
    Bracket cover
    Bracket base
    1 Remove the Euroblock connector.
    2 After loosening the terminal screws of the Euroblock connector with a
    flat-blade screwdriver, insert the cable into each terminal and tighten
    the screws. Make sure that cables cannot be pulled out.
    NOTE
    Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).
    There are two acceptable wiring methods.
    CAUTION
    When connecting with low impedance, take note of the combined
    resistance.
    Using Loop-Through Terminals
    For this method, cables are connected from terminals 1 and 4 to the
    subsequent speaker. If the Euroblock connector is disconnected from
    a speaker, all subsequent speakers will not work. This can be useful
    to identify which speaker has a problem.
    Paralleling Input Terminals
    For this method, cables are connected to terminals 2 and 3 of each
    speaker. Since the cables are connected via Euroblock connectors,
    subsequent speakers can work even if a problem occurs with a
    speaker.
    2
    CONNECT THE WIRING TO THE CONNECTOR
    Euroblock connector
    Euroblock connector
    Less than 3 mm (0.1 in.)
    From amplifier or
    previous speakers
    To subsequent
    speakers
    To
    subsequent
    speakers
    Euroblock
    connector
    Power
    amplifier
    Speaker
    From amplifier or
    previous speakers
    To subsequent
    speakers
    Power
    amplifier
    Speaker
    Euroblock
    connector
    To
    subsequent
    speakers
    Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/
    70V line distributed system, by rotating the tap selector switch on the rear
    side of the speaker with a flat-blade screwdriver.
    CAUTION
    The “X” position should not be selected. The 8Ω position should be
    selected for 8Ω audio systems only. If the setting is incorrect, it may
    cause malfunction of the speaker and amplifier.
    Make sure the amplifier is switched off before operating the tap selector
    switch.
    1 Attach the mounting bracket and safety wire to the speaker. Use the
    supplied screws to attach the mounting bracket.
    The way to attach the mounting bracket depends on the orientation of
    the speaker (vertical or horizontal).
    2 Set the desired vertical angle of the speaker.
    Loosen the angle adjustment bolt with the supplied hexagon wrench,
    adjust the angle of the speaker, and tighten the angle adjustment bolt
    to fix the speaker (indication of torque: 8 N·m).
    NOTE
    Guide marked on the mounting bracket is every 10°.
    (VXS8/VXS8W only) When installing the speaker to the wall with a
    vertical angle of 30° or less, attach the supplied stopper screw.
    1 Install the mounting bracket to the bracket base.
    3
    SET THE LINE VOLTAGE/IMPEDANCE AND POWER
    4
    ATTACH THE MOUNTING BRACKET AND SAFETY WIRE
    NOTE
    Mounting bracket can be attached in reverse direction.
    5
    INSTALL THE SPEAKER TO THE BRACKET BASE AND FIX
    THE CABLE
    Illustration indicates the setting at 30 W for 100 V
    line and 15 W for 70 V line.
    Mounting bracket
    Safety wire
    Stopper screw
    (VXS8/VXS8W only)
    Vertical installation
    Angle
    adjustment bolt
    Angle adjustment
    bolt
    Horizontal installation
    Stopper screw
    (VXS8/VXS8W only)
    To the wall To the ceiling
    2 Attach the safety pin.
    Be sure to attach the safety pin to prevent the mounting bracket from
    falling.
    NOTE
    The safety pin can be attached from either side of the mounting
    bracket depending on the angle of the speaker.
    3 Plug the Euroblock connector into the socket in the speaker.
    4 Attach the terminal cover.
    5 (If installing the speaker to the wall) turn the speaker horizontally to
    set the angle.
    6 Make sure the mounting bracket is seated against the bracket base,
    then tighten the supplied bolt (indication of torque: 6.5 N·m).
    NOTE
    When installing the speaker to the ceiling in particular, make sure
    the mounting bracket is seated against the bracket base.
    The bolt with hexagon hole can be attached from either side of the
    mounting bracket (left or right) depending on the angle of the
    speaker.
    7 Install the safety wire to the wall/ceiling.
    CAUTION
    Make sure to take measures to prevent the speaker from falling
    down in the event of a installation failure.
    When installing the safety wire to the wall, install it higher than the
    wire’s attachment point on the speaker, with as little slack as
    possible.
    If the safety wire is too short, prepare another wire appropriate for
    the speaker weight and installation conditions. If the wire is too
    long, should the speaker fall, the wire may snap as a result of too
    much strain.
    Safety pin
    Terminal cover
    Bolt with hexagon hole
    Owner’s Manual
    Surface Mount Speaker
    English
    ZE85530
    EN
Yamaha VXS8

Behöver du hjälp?

Antal frågor: 0

Behöver du hjälp eller har du en fråga om Yamaha VXS8? Ställ din fråga här. Lämna en tydlig och omfattande beskrivning av ditt problem och din fråga. Ju mer information du anger desto enklare blir det för andra ägare av Yamaha VXS8 att svara på din fråga.

Se manualen för Yamaha VXS8 helt gratis här nedan. Den här manualen tillhör kategorin och har betygsatts av 1 personer med ett genomsnitt på 7.5. Den här manualen är tillgänglig på följande språk: Engelsk. Behöver du hjälp eller har du en fråga om Yamaha VXS8? Ställ din fråga här

Yamaha VXS8 – specifikationer

Varumärke Yamaha
Modell VXS8
Produkt Högtalare
EAN 4957812526906, 0086792972473
Språk Engelsk
Filtyp PDF
Prestanda
Rekommenderad användning Universal
Basreflex
Material, hölje Akrylnitrilbutadienstyren (ABS)
Produktens färg Vit
Certifiering UL1480, NFPA70, CE, EAC, RoHS
Högtalare
Högtalartyp 2-vägs
Högtalarplacering Ceiling-mountable, Wall-mountable
Antal förare 2
Audio
Frekvensområde 51 - 20000
Övergångsfrekvens 2800
Uteffekt (RMS) 180
Impedans 8
Känslighet 91
Anslutningar
Anslutningsteknologi Kabel
- Phoenix/Euroblock
Vikt & dimension
Bredd 278
Djup 239
Höjd 430
Vikt 8200
Förpackningens innehåll
Monteringsfästen ingår
Övrigt
Antal Euroblock-input-anslutningar 1

Relaterade produktmanualer

Högtalare Yamaha

Vanliga frågor

Nedan hittar du de vanligaste frågorna om YamahaVXS8 .

Är din fråga inte listad? Ställ din fråga här

Bruksanvisni.ng

Letar du efter en manual? Bruksanvisni.ng säkerställer att du hittar manualen som du letar efter på nolltid. Vår databas innehåller mer än 1 miljon PDF-manualer från över 10 000 märken. Varje dag lägger vi till de senaste manualerna så att du alltid hittar produkten du letar efter. Det är väldigt enkelt: ange bara märket och typen av produkt i sökrutan för att omedelbart semanualen du önskar online helt gratis.

Bruksanvisni.ng

© Copyright 2020 Bruksanvisni.ng. All Rights Reserved.

Vi använder cookies för att se till att vi ger dig den bästa upplevelsen på vår hemsida. Om du fortsätter att använda den här webbplatsen kommer vi att anta att du godkänner detta.

Läs mer